MAX746 Maxim, MAX746 Datasheet - Page 15

• Manufacturer Part Number: MAX746
• Description: High-Efficiency / PWM / Step-Down / N-Channel DC-DC Controller
• Manufacturer: Maxim

Increasing C7 by up to 50% enhances outer-loop
stability by adding stability to the inductor current
waveform. But increasing C7 too much causes
FB’s response time to decrease (due to the larger
RC time constant caused by the feedback resistors
and the compensation capacitor), which reduces
load-transient stability.
Select R1 between 10kΩ and 1MΩ. Determine R2 using
the following equation:
where V
(e.g., 100kΩ) between LBO and V
If a secondary power supply (a minimum of 5V above
the main supply) is available, it can be substituted for
the charge-pump high-side supply. In this case,
bypass HIGH with a 1µF capacitor and leave CP
unconnected. Since this secondary supply voltage
is applied to the gate, V
gate-source breakdown voltage of the external N-FET.
Also, the voltage at HIGH must not exceed 20V. If
a secondary supply is used, the shutdown function
cannot be used because HIGH is internally tied to
V+ in shutdown mode. In this case, SHDN must be
tied low. With the main supply off and HIGH at 12V,
HIGH will typically sink 130µA.
Because high current levels and fast switching wave-
forms radiate noise, proper PC board layout is essen-
tial. Use a ground plane, and minimize ground noise by
connecting GND, the anode of the steering Schottky
diode, the input bypass-capacitor ground lead, and the
output filter capacitor ground lead to a single point (star
ground configuration). Also minimize lead lengths to
reduce stray capacitance, trace resistance, and radiat-
ed noise. Place bypass capacitor C3 as close to V+
and GND as possible.
AV+ and CS are the inputs to the differential-input
current-sense amplifier. Use a Kelvin connection
across the sense resistor, as shown in Figure 8.
Although AV+ also functions as the supply voltage
for sensitive analog circuitry, a separate AV+ bypass
capacitor should not be used. By not using a capaci-
REF
is typically 2.0V. Connect a pull-up resistor
R2 = R1
______________________________________________________________________________________
Place of the Charge Pump
(
Using a Second Supply in
________________
Setting the Low-Battery
(V
Layout Considerations
TRIP
GS
V
REF
OUT
must not exceed the
- V
Detector Voltage
High-Efficiency, PWM, Step-Down,
REF
(Figure 5).
)
)
N-Channel DC-DC Controller
tor, any noise at the CS input will also appear at the
AV+ input, and will be interpreted by the current-
sense amplifier as a common-mode signal . A sepa-
rate AV+ capacitor causes the noise to appear on
only one input, and this differential noise will be
amplified, adversely affecting circuit operation.
When probing the MAX746 circuit, avoid shorting
V+ to GND (the two pins are adjacent) as this may
cause the IC to malfunction because of large ground
currents. Because of its fast switching and high drive-
capability requirements, EXT is a low-impedance point
that is not short-circuit protected. Therefore, do not
short EXT to any node (including AGND and V+, which
are adjacent to EXT).
Similarly, CC (or FB in adjustable-output operation) is a
sensitive input that should not be shorted to any node.
Avoid shorting CC when probing the circuit, as this may
damage the device.
The MAX746 may continue to operate with AV+ discon-
nected, but erratic switching waveforms will appear at EXT.
There is a region between CCM and DCM where the
inductor current operates in both modes, as shown
in the Idle-Mode Moderate Current EXT waveform in
the Typical Operating Characteristics . As the out-
put voltage varies, it is fed back into CC and the
duty cycle adjusts to compensate for this change.
The switch is considered off when V
Figure 8. Kelvin Connection for Current-Sense Amplifier
V
IN
MAX746
V+
AV+
EXT
CS
R SENSE
Switching Waveforms
Additional Notes
N
EXT
L1
is less than
KELVIN SENSE
CONNECTION
V
OUT
15