LPC2210 Philips Semiconductors (Acquired by NXP), LPC2210 Datasheet - Page 6

• Manufacturer Part Number: LPC2210
• Description: 16/32-bit Arm Microcontroller; With 10-bit ADC And External Memory Interfacethe LPC2210 is Based on a 16/32 Bit ARM7TDMI-STM Cpu With Real-time Emulation And Embedded Trace Support. For Critical Code Size Applications, The Alternative 16-bit Thumb Mo
• Manufacturer: Philips Semiconductors (Acquired by NXP)

Philips Semiconductors
Table 3:
9397 750 12872
Preliminary data
Symbol
P0.11
P0.12
P0.13
P0.14
P0.15
P0.16
P0.17
P0.18
P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
P0.27
Pin description
Pin
83
84
85
92
99
100
101
121
122
123
4
5
6
8
21
23
…continued
Type
I
O
O
O
I
I
I
O
I
I
I/O
O
I
I/O
O
O
I/O
I
O
I
I
O
I
I
O
I/O
I/O
I/O
I
I
O
I
I
I
I
Description
CTS1 — Clear to Send input for UART1.
CAP1.1 — Capture input for Timer1, channel 1.
DSR1 — Data Set Ready input for UART1.
MAT1.0 — Match output for Timer1, channel 0.
DTR1 — Data Terminal Ready output for UART1.
MAT1.1 — Match output for Timer1, channel 1.
DCD1 — Data Carrier Detect input for UART1.
EINT1 — External interrupt 1 input.
Note: LOW on this pin while RESET is LOW forces on-chip boot-loader to
take over control of the part after reset.
RI1 — Ring Indicator input for UART1.
EINT2 — External interrupt 2 input.
EINT0 — External interrupt 0 input.
MAT0.2 — Match output for Timer0, channel 2.
CAP0.2 — Capture input for Timer0, channel 2.
CAP1.2 — Capture input for Timer1, channel 2.
SCK1 — Serial Clock for SPI1. SPI clock output from master or input to slave.
MAT1.2 — Match output for Timer1, channel 2.
CAP1.3 — Capture input for Timer1, channel 3.
MISO1 — Master In Slave Out for SPI1. Data input to SPI master or data
output from SPI slave.
MAT1.3 — Match output for Timer1, channel 3.
MAT1.2 — Match output for Timer1, channel 2.
MOSI1 — Master Out Slave In for SPI1. Data output from SPI master or data
input to SPI slave.
CAP1.2 — Capture input for Timer1, channel 2.
MAT1.3 — Match output for Timer1, channel 3.
SSEL1 — Slave Select for SPI1. Selects the SPI interface as a slave.
EINT3 — External interrupt 3 input.
PWM5 — Pulse Width Modulator output 5.
CAP1.3 — Capture input for TIMER1, channel 3.
CAP0.0 — Capture input for Timer0, channel 0.
MAT0.0 — Match output for Timer0, channel 0.
General purpose bidirectional digital port only.
General purpose bidirectional digital port only.
General purpose bidirectional digital port only.
AIN0 — A/D converter, input 0. This analog input is always connected to its
pin.
CAP0.1 — Capture input for Timer0, channel 1.
MAT0.1 — Match output for Timer0, channel 1.
Rev. 01 — 09 February 2004
16/32-bit ARM microcontrollers with external memory interface
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
LPC2210
6 of 39