LPC2194JBD64 Philips Semiconductors (Acquired by NXP), LPC2194JBD64 Datasheet - Page 6

• Manufacturer Part Number: LPC2194JBD64
• Description: Single-chip 16/32-bit Microcontrollers; 256 KB Isp/iap Flash With 10-bit ADC And CAN.the LPC2194 is Based on a 16/32 Bit ARM7TDMI-STM Cpu With Real-time Emulation And Embedded Trace Support, Together With 256 Kilobytes (kB) of Embedded High Speed Fla
• Manufacturer: Philips Semiconductors (Acquired by NXP)

Philips Semiconductors
Table 3:
9397 750 12757
Preliminary data
Symbol
P0.12
P0.13
P0.14
P0.15
P0.16
P0.17
P0.18
P0.19
P0.20
P0.21
P0.22
P0.23
P0.24
P0.25
Pin description
Pin
38
39
41
45
46
47
53
54
55
1
2
3
5
39
…continued
Type
I
I
O
I
O
O
O
I
I
I
I
I
O
I
I
I/O
O
I
I/O
O
O
I/O
I
O
I
I
O
I
O
I
O
I
O
O
Description
CAP1.1 — Capture input for Timer1, channel 1.
DSR1 — Data Set Ready input for UART1.
MAT1.0 — Match output for Timer1, channel 0.
RD4 — CAN4 receiver input.
DTR1 — Data Terminal Ready output for UART1.
MAT1.1 — Match output for Timer1, channel 1.
TD4 — CAN4 transmitter output.
DCD1 — Data Carrier Detect input for UART1.
EINT1 — External interrupt 1 input.
Note: LOW on this pin while RESET is LOW forces on-chip boot-loader to
take over control of the part after reset.
RI1 — Ring Indicator input for UART1.
EINT2 — External interrupt 2 input.
EINT0 — External interrupt 0 input.
MAT0.2 — Match output for Timer0, channel 2.
CAP0.2 — Capture input for Timer0, channel 2.
CAP1.2 — Capture input for Timer1, channel 2.
SCK1 — Serial Clock for SPI1. SPI clock output from master or input to slave.
MAT1.2 — Match output for Timer1, channel 2.
CAP1.3 — Capture input for Timer1, channel 3.
MISO1 — Master In Slave Out for SPI1. Data input to SPI master or data
output from SPI slave.
MAT1.3 — Match output for Timer1, channel 3.
MAT1.2 — Match output for Timer1, channel 2.
MOSI1 — Master Out Slave In for SPI1. Data output from SPI master or data
input to SPI slave.
CAP1.2 — Capture input for Timer1, channel 2.
MAT1.3 — Match output for Timer1, channel 3.
SSEL1 — Slave Select for SPI1. Selects the SPI interface as a slave.
EINT3 — External interrupt 3 input.
PWM5 — Pulse Width Modulator output 5.
RD3 — CAN3 receiver input.
CAP1.3 — Capture input for Timer1, channel 3.
TD3 — CAN3 transmitter output.
CAP0.0 — Capture input for Timer0, channel 0.
MAT0.0 — Match output for Timer0, channel 0.
RD2 — CAN2 receiver input.
TD2 — CAN2 transmitter output.
RD1 — CAN1 receiver input.
Rev. 01 — 06 February 2004
Single-chip 16/32-bit microcontrollers
© Koninklijke Philips Electronics N.V. 2004. All rights reserved.
LPC2194
6 of 33