FT230XQ-R International Semiconductor Technologies, FT230XQ-R Datasheet - Page 11

• Manufacturer Part Number: FT230XQ-R
• Description: Specifications: Number of Channels: 1, UART ; Lead Free Status: Lead Free ; RoHS Status: RoHS Compliant
• Manufacturer: International Semiconductor Technologies

CBUS Signal
BCD Charger#
BitBang_WR#
BitBang_RD#
BCD Charger
TX&RXLED#
TRI-STATE
CLK24MHz
CLK12MHz
3.3 CBUS Signal Options
The following options can be configured on the CBUS I/O pins. CBUS signal options are common to both
package versions of the FT230X. These options can be configured in the internal MTP memory using the
software utility FT_PROG or MPROG, which can be downloaded from the FTDI Utilities
(www.ftdichip.com). The default configuration is described in Section 8.
CLK6MHz
PWREN#
Option
DRIVE 1
DRIVE 0
TXLED#
RXLED#
SLEEP#
TXDEN
GPIO
Copyright © 2013 Future Technology Devices International Limited
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
CBUS0, CBUS1, CBUS2, CBUS3
Available On CBUS Pin
IO Pad is tri-stated
Output a constant 1
Output a constant 0
Enable transmit data for RS485
Output is low after the device has been configured by
USB, then high during USB suspend mode. This output
can be used to control power to external logic P-Channel
logic level MOSFET switch. Enable the interface pull-down
option when using the PWREN# in this way.
Transmit data LED drive – pulses low when transmitting
data via USB. See Section 7.5 for more details.
Receive data LED drive – pulses low when receiving data
via USB. See Section 7.5 for more details.
LED drive – pulses low when transmitting or receiving
data via USB. See Section 7.5 for more details.
Goes low during USB suspend mode. Typically used to
power down an external TTL to RS232 level converter IC
in USB to RS232 converter designs.
24 MHz Clock output.*
12 MHz Clock output.*
6 MHz Clock output.*
CBUS bit bang mode option. Allows up to 4 of the CBUS
pins to be used as general purpose I/O. Configured
individually for CBUS0, CBUS1, CBUS2 and CBUS3 in the
internal MTP
AN232R-01, available from FTDI website
(www.ftdichip.com) describes in more detail how to use
CBUS bit bang mode.
Battery charge Detect, indicates when the device is
connected to a dedicated battery charger host. Active
high output.
Inverse of BCD Charger
Synchronous and asynchronous bit bang mode WR#
strobe output.
Synchronous and asynchronous bit bang mode RD#
strobe output.
Document No.: FT_000566 Clearance No.: FTDI# 260
FT230X USB TO BASIC UART IC
memory
Description
. A separate application note,
Version 1.2
11