AAT2689 Analogic Corporation, AAT2689 Datasheet - Page 14

• Manufacturer Part Number: AAT2689
• Manufacturer: Analogic Corporation

Typical output capacitor values for maximum output cur-
rent conditions range from 1μF to 10μF. Applications
utilizing the exceptionally low output noise and optimum
power supply ripple rejection characteristics of channel
2 should use 2.2μF or greater for C
may be increased without limit. In low output current
applications where output load is less than 10mA, the
minimum value for C
Channel 2 Enable Function
The AAT2689 features an LDO regulator enable/disable
function. This pin (EN) is active high and is compatible
with CMOS logic. To assure the LDO regulator will switch
on, the EN turn-on control level must be greater than
1.5V. The LDO regulator will go into disable shutdown
mode when the voltage on the EN pin falls below 0.6V.
If the enable function is not needed in a specific applica-
tion, it may be tied to V
continuously on state. When the LDO regulator is in
shutdown mode, an internal 1.5kΩ resistor is connected
between V
C
1.5kΩ has no adverse effect on device turn-on time.
Channel 2 Short-Circuit Protection
The AAT2689 LDO contains an internal short-circuit pro-
tection circuit that will trigger when the output load cur-
rent exceeds the internal threshold limit. Under short-
circuit conditions, the output of the LDO regulator will be
current limited until the short-circuit condition is removed
from the output or LDO regulator package power dissi-
pation exceeds the device thermal limit.
Channel 2 Thermal Protection
The AAT2689 LDO has an internal thermal protection
circuit which will turn on when the device die tempera-
ture exceeds 150°C. The internal thermal protection
circuit will actively turn off the LDO regulator output
pass device to prevent the possibility of over tempera-
ture damage. The LDO regulator output will remain in a
shutdown state until the internal die temperature falls
back below the 150°C trip point. The combination and
interaction between the short circuit and thermal protec-
tion systems allows the LDO regulator to withstand
indefinite short-circuit conditions without sustaining per-
manent damage.
14
SystemPower
OUT
when the LDO regulator is disabled. The internal
OUT
TM
and GND. This is intended to discharge
PMIC Solution for 12V Adapter Systems with 2-Output High Performance Step-Down Converters
OUT
IN
can be as low as 0.47μF.
to keep the LDO regulator in a
OUT
. If desired, C
w w w . a n a l o g i c t e c h . c o m
OUT
Channel 2 No-Load Stability
The AAT2689 is designed to maintain output voltage
regulation and stability under operational no load condi-
tions. This is an important characteristic for applications
where the output current may drop to zero.
Channel 2 Reverse Output-to-Input
Voltage Conditions and Protection
Under normal operating conditions, a parasitic diode
exists between the output and input of the LDO regula-
tor. The input voltage should always remain greater than
the output load voltage, maintaining a reverse bias on
the internal parasitic diode. Conditions where V
exceed V
bias the internal parasitic diode and allow excessive cur-
rent flow into the V
regulator. In applications where there is a possibility of
V
mal operation, the use of a larger value C
highly recommended. A larger value of C
to C
down, thus preventing V
cations where there is a greater danger of V
ing V
to place a Schottky diode across V
the cathode to V
diode forward voltage should be less than 0.45V.
Thermal Calculations
There are three types of losses associated with the
AAT2689 step-down converter: switching losses, con-
duction losses, and quiescent current losses. Conduction
losses are associated with the R
the power output switching devices. Switching losses are
dominated by the gate charge of the power output
switching devices. At full load, assuming continuous con-
duction mode (CCM), a simplified form of the synchro-
nous step-down converter and LDO losses is given by:
I
cent currents respectively. The term t
mate the full load step-down converter switching losses.
P
Q1
OUT
TOTAL
and I
OUT
exceeding V
IN
for extended periods of time, it is recommended
+ (t
=
will effect a slower C
Q2
IN
I
OUT1
SW
are the step-down converter and LDO quies-
should be avoided since this would forward
· F
2
· (R
S
IN
· I
IN
for brief amounts of time during nor-
DS(ON)H
OUT1
OUT
and anode to V
PRODUCT DATASHEET
+ I
pin, possibly damaging the LDO
OUT
· V
Q1
from exceeding V
) · V
OUT1
IN
V
AAT2689
IN1
IN1
decay rate during shut-
+ R
DS(ON)
+ (V
IN
DS(ON)L
to V
OUT
SW
IN2
characteristics of
). The Schottky
2689.2008.06.1.0
is used to esti-
OUT
- V
· [V
IN
IN
with respect
OUT2
(connecting
capacitor is
IN1
IN
OUT
. In appli-
OUT
) · I
- V
exceed-
OUT1
might
OUT2
])