MCP6064 Microchip Technology, MCP6064 Datasheet - Page 15
![no-image](/images/manufacturer_photos/0/4/439/microchip_technology_sml.jpg)
MCP6064
Manufacturer Part Number
MCP6064
Description
(MCP6061 - MCP6064) High Precision Op Amps
Manufacturer
Microchip Technology
Datasheet
1.MCP6064.pdf
(34 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
MCP6064-E/SL
Manufacturer:
MICROCHIP
Quantity:
12 000
Part Number:
MCP6064-E/SL
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
MCP6064-E/ST
Manufacturer:
MICROCHIP
Quantity:
12 000
Company:
Part Number:
MCP6064T-E/SL
Manufacturer:
MICROCHIP
Quantity:
12 000
Part Number:
MCP6064T-E/SL
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
Company:
Part Number:
MCP6064T-E/ST
Manufacturer:
MICROCHIP
Quantity:
12 000
Part Number:
MCP6064T-E/ST
Manufacturer:
MICROCHIP/微芯
Quantity:
20 000
www.DataSheet4U.com
4.0
The MCP6061/2/4 family of op amps is manufactured
using Microchip’s state-of-the-art CMOS process and
is specifically designed for low-power, high precision
applications.
4.1
4.1.1
The MCP6061/2/4 op amps are designed to prevent
phase reversal when the input pins exceed the supply
voltages.
exceeding the supply voltage without any phase
reversal.
4.1.2
The ESD protection on the inputs can be depicted as
shown in
protect the input transistors and to minimize input bias
current (I
when they try to go more than one diode drop below
V
V
normal operation and low enough to bypass ESD
events within the specified limits.
FIGURE 4-1:
Structures.
In order to prevent damage and/or improper operation
of these op amps, the circuit they are in must limit the
voltages and currents at the V
Section 1.1 “Absolute Maximum Ratings †” at the
beginning of Section 1.0 “Electrical Characteris-
tics”).
to protecting these inputs. The internal ESD diodes
prevent the input pins (V
below ground, and the resistors R
possible current drawn out of the input pins. Diodes D
and D
going too far above V
shown, resistors R
through D
© 2009 Microchip Technology Inc.
SS
DD
. They also clamp any voltage that go too far above
; their breakdown voltage is high enough to allow
V
V
V
IN
2
DD
SS
Figure 4-2
+
prevent the input pins (V
APPLICATION INFORMATION
Rail-to-Rail Input
B
1
). The input ESD diodes clamp the inputs
Figure
Figure 2-34
Bond
Bond
Bond
and D
PHASE REVERASAL
INPUT VOLTAGE AND CURRENT
LIMITS
Pad
Pad
Pad
2
4-1. This structure was chosen to
shows the recommended approach
.
1
and R
Simplified Analog Input ESD
IN
Stage
Input
DD
shows
+ and V
. When implemented as
2
IN+
also limit the current
IN
the
IN
-) from going too far
and V
1
+ and V
Bond
and R
Pad
input
IN-
2
V
pins (see
IN
limit the
IN
voltage
-) from
–
1
FIGURE 4-2:
Inputs.
It is also possible to connect the diodes to the left of the
resistors R
the diodes D
mechanism. The resistors then serve as in-rush current
limiters; the DC currents into the input pins (V
V
current can flow out of the inputs when the common
mode voltage (V
Figure
4.1.3
The input stage of the MCP6061/2/4 op amps uses two
differential input stages in parallel. One operates at a
low common mode input voltage (V
operates at a high V
operates with a V
300 mV below V
voltage is measured at V
V
The transition between the input stages occurs when
V
Figure
gain linearity, with non-inverting gains, avoid this region
of operation.
4.2
The output voltage range of the MCP6061/2/4 op amps
is V
(maximum) when R
and V
more information.
IN
DD
CM
-) should be very small. A significant amount of
+ 0.3V to ensure proper operation.
SS
is near V
V
V
DD
2-36).
2-6). For the best distortion performance and
1
2
+ 15 mV (minimum) and V
Rail-to-Rail Output
R
R
= 6.0V. Refer to
1
1
2
NORMAL OPERATION
and R
1
>
>
and D
R
R
V
V
1
2
DD
D
SS
SS
SS
1
CM
2
CM
. (See
– (minimum expected V
– (minimum expected V
– 1.1V (See
. In this case, the currents through
2
MCP6061/2/4
L
CM
) is below ground (V
need to be limited by some other
D
= 10 kΩ is connected to V
Protecting the Analog
up to 300 mV above V
. With this topology, the device
2
Figure
Figures 2-27
2 mA
2 mA
CM
MCP606X
2-13) .The input offset
Figures
V
= V
R
CM
DD
3
DS22189A-page 15
), while the other
SS
DD
and
2-4,
– 0.3V and
1
2
)
)
SS
– 15 mV
2-5
2-28
IN
). (See
DD
+ and
DD
and
and
for
/2