RN470K1HBK-1016P Lelon, RN470K1HBK-1016P Datasheet - Page 6

no-image

RN470K1HBK-1016P

Manufacturer Part Number
RN470K1HBK-1016P
Description
Specifications: Manufacturer: Lelon ; Product Category: Aluminum Electrolytic Capacitors - Leaded ; RoHS:  Details ; Capacitance: 47 uF ; Tolerance: 10 % ; Voltage Rating: 50 Volts ; Operating Temperature Range: - 40 C to + 85 C ; Termination St
Manufacturer
Lelon
Datasheet
Endurance Characteristic:
No.
1
2
3
4
5
6
7
Temperature Test
Endurance Life
Unload Life Test
Test
Resistance Test
Rotational
High Temperature
High Temperature
Humidity Test
Low Temperature
Vibration Test
Solder Heat-
Item
Capacitor is placed in an oven whose temperature
follow specific regulation to +25℃(3 min.) →
-40℃(30 min.) →+25℃(3 min.) → +85℃(30 min.)
→+25℃(3 min.)”, and it is called a cycle. The test
totals 50 cycles. And then the capacitor shall be
subjected to standard atmospheric conditions for
4 hours, after which measurements shall be made.
1. Capacitors shall be placed in oven with
2. The capacitor should be used within specified
3. The specified maximum permissible ripple
4. Then the capacitor shall be subjected to
5. After application of the rated voltage at 85℃,
After 1000+48/-0 hrs test at 85℃ without rated
working voltage. And then the capacitor shall be
subjected to standard atmospheric conditions for
4 hours, after which measurements shall be made.
The rated voltage shall be applied to the capacitors
before the measurenments for 160 ~ 250V
(Refer to JIS C 5101-4 4.1)
Capacitors shall be exposed for 1000+48/-0 hrs
in an atmosphere of 90%~95% R.H. at 60±3℃
And then the capacitor shall be subjected to
standard atmospheric conditions for 4 hours,
after which measurements shall be made.
Capacitors are placed at –40 ±3℃ for 96±4 hrs.
And then the capacitor shall be subjected to
atmospheric conditions for 4 hours, after which
measurements shall be made.
1. Fix it at the point 4mm or less form body.
2. Direction and during of vibration:
3. Frequency:
4. Total amplitude : 1.5mm
The section of lead below 4mm form the body of
capacitor must be immersed in 260±5℃ liquid tin
10±1 seconds ,than, after removing the following
specifications shall be satisfied when capacitor
terminal is restored to 20℃ over 4 hours.
application of ripple current and rated voltage
for 2000+72/-0 hrs at 85℃.
permissible ripple current in each standard
products table (the sum of DC voltage and
AC peak voltage shall be equal to the rated
DC working voltage).
current in defined at 85℃ and 120Hz
(unless otherwise specified).
standard atmospheric conditions for 4 hours,
after which measurements shall be made.
the polarity inverted every 250 hours.
For ones of 12.5mm or more in diameter or
25mm or more length, use separate fixture.
3 orthogonal directions mutually each for
2 hrs (total of 6 hrs).
10 to 55 Hz reciprocation for 1min.
Conditions
Capacitance
change
Tanδ
Leakage
Current
Physical
Capacitance
change
Tanδ
Leakage
Current
Physical
Capacitance
change
Leakage
Current
Physical
Capacitance
change
Tanδ
Leakage
Current
Physical
Capacitance
change
Tanδ
Leakage
Current
Physical
Capacitance
change
Tanδ
Leakage
Current
Physical
Capacitance
change
Tanδ
Leakage
Current
Physical
Tanδ
Within±10% of initial value.
Within specified value
Within specified value
No broken and undamaged
Within ±20% of initial value.
Less than 200% of specified value
Within specified value
No broken and undamaged
Within ±20% of initial value.
Less than 200% of specified value
Within specified value
No broken and undamaged
Within ±10% of initial value.
Less than 120% of specified value
Within specified value
No broken and undamaged
Within ±10% of initial value.
Within specified value
Within specified value
No broken and undamaged
Within ±10% of initial value.
Within specified value
Within specified value
No broken and undamaged
Within ±10% of initial value.
Within specified value
Within specified value
No broken and undamaged
Specification
- 1 -

Related parts for RN470K1HBK-1016P