VCC6-Q/R Vectron International, VCC6-Q/R Datasheet
![no-image](/images/no-image-200.jpg)
VCC6-Q/R
Related parts for VCC6-Q/R
VCC6-Q/R Summary of contents
Page 1
... The VCC6 Crystal Oscillator Enable/Disable Output Buffer / Disable Vectron International 267 Lowell Road, Hudson NH 03051 VCC6-Q/R Series 2.5 and 3.3 volt LVPECL Crystal Oscillator Features 2.5 or 3.3V LVPECL rd 3 Overtone Crystal for best jitter performance Output frequencies to 270 MHz Low Jitter < rms, 12kHz to 20MHz Enable/Disable for test and board debug -10/70 or – ...
Page 2
... VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator Performance Characteristics Table 1. Electrical Performance Parameter Frequency 1 Supply Voltage , 3.3V Q option 2.5V R option Supply Current Output Logic Levels, 0/70°C 2 Output Logic High 2 Output Logic Low Output Logic Levels, -40/85°C 2 Output Logic High 2 Output Logic Low Transition Times ...
Page 3
... VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator Outline Diagram and Pin Out Table 2. VCC6-QAx Pinout Pin # Symbol E/D 3 GND Figure 3 Optional VCC6-QAx Package Drawing Table 3. VCC6-QCx Pinout Pin # Symbol 1 E GND Figure 4. VCC6-QCx and VCC6-QAx Package Drawing ...
Page 4
... VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator Terminating PECL Outputs The VCC6 incorporates a standard PECL output scheme, which are un-terminated emitters as shown in Figure 5. There are numerous application notes on terminating and interfacing PECL logic and the two most common methods are a single resistor to ground, Figure 6, and a pull-up/pull-down scheme as shown in Figure 7 ...
Page 5
... VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator Enable/Disable Functional Description Under normal operation the Enable/Disable is left open, or set to a logic high state, and the VCC6 is in oscillation mode and outputs are enabled (active). When the E/D is set to a logic low, the oscillator stops and the both the output and complementary outputs are in a high impedance state ...
Page 6
... VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator IR Reflow and Suggested Pad Size Layout The VCC6 has been qualified to meet the JEDEC standard for Pb-Free assembly. The temperatures and time intervals listed are based on the Pb-Free small body requirements and maximum parameters are listed in Table 6, lower temperatures are also acceptable. The VCC6 is hermetically sealed so an aqueous wash is not an issue. Frequencies > ...
Page 7
... VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator Tape and Reel Table 8. Tape and Reel Dimensions (mm) Tape Dimensions Product VCC6 16 7.5 1.5 Vectron International 267 Lowell Rd, Hudson NH 03051 Figure 10. Tape and Reel Diagram Reel Dimensions Tel: 1-88-VECTRON-1 ...
Page 8
... VCC6-Q/R Series, 2.5 and 3.3v PECL Crystal Oscillator Table 9. Standard Frequencies (MHz) 19.440 27.000 40.000 40.680 64.000 64.375 80.000 83.125 98.304 100.000 125.000 130.000 136.000 143.000 156.000 156.250 160.160 161.1328 166.6286 166.6667 171.000 173.3707 195.3125 200.000 Other frequencies may be available upon request. Standard frequencies are frequencies which the crystal has been designed and does not imply a stock position ...