D4SL-NSK10-LKx Omron, D4SL-NSK10-LKx Datasheet - Page 26

• Manufacturer Part Number: D4SL-NSK10-LKx
• Description: Guard Lock Safety-door Switch
• Manufacturer: Omron

26
D4SL-N / D4SL-NSK10-LK@
D4SL-NSK10-LK@
Approriate Tightening Torque
Technical Specifications
Nomenclature
• Use this product for a lightweight door (20 kg max). Otherwise the
• This product is for D4SL-N Guard Lock Safety-door Switch only.
• Use the Slide Handle in the direction A or B in the following figure.
• Loose screws may result in malfunction. Use washers and tighten
Slide Key mounting screw (M6)
Operation key special mounting screw
(screws supplied)
Switch special mounting screw
(screws supplied)
Inner Lever
Ambient operating temperature
Ambient operating humidity
Mechanical durability
• Do not store the Switch where corrosive gases (e.g., H
• Perform maintenance inspections periodically.
• When the lockout key is attached to your wrist, be careful that the
product may be damaged.
This product cannot be used with any other manufacturer's door
switches.
the screws to the specified torques. Mount the Slide Base at four
points with screws. Adding adhesive is recommended for
preventing the screws from loosening.
Also, when mounting the Product to a door for disable-prevention
purposes, purchase and use tamper-resistant screws.
NH
temperature or humidity.
strap does not get stuck in equipment.
3
, HNO
B
3
or Cl
Slide Key Unit
FREE
SLIDE
LOCK
SLIDE
2
) or dust is present, or in locations subject to high
Guide
Release Key
D4SL-N Guard Lock Safety-door Switch
Operation Key
Lockout key
Shot Bolt
Slide Base
LOCK
SLIDE
−10 to 55°C (with no icing)
95% max.
20,000 operations min.
FREE
SLIDE
A
Slide Handle
0.75 to 1.15 N•m
6.0 to 7.0 N•m
2.4 to 2.8 N•m
9 to 10 N•m
2
S, SO
2
,
Differences between Lockout Key and Trapped Key
(Reference)
Mounting of innner lever
Mounting method
1) Detaching of mounting screw
Remove the handle mounting screw with TORX screwdriver (T30).
2) Mounting of inner lever
Tighten A portion of the inner lever to a suitable torque with wrench
(width across flat: 10mm).
Closing
the door
Opening
the door
• When mounting the operation key, line up the inside edges of the
• Use the supplied special screws to mount the operation key and
• To tighten the screws, use the tip of a flat-head screwdriver on the
• The special screws cannot be removed once they are tightened.
• This product is for Omron, the D4SL-NSK10 and the D4GL-SK10
• Do not operate the handle with the handle mounting screw
• Be careful not to lose the spring washer and hexagonal nut when
• Loose inner lever may result in malfunction. Use washers and
Spring washer
(M6)
www.DataSheet.co.kr
Spring washer
(M6)
long operation key holes with the outer edges of the slide handle
as in the following figure to ensure easy position adjustment.
D4SL-N Guard Lock Safety-door Switch.
screw heads as shown in the following figure.
only. This product cannot be used with any other products.
removed. Doing so may result in malfunction.
remove the handle mounting screw. (Fig.1)
tighten the inner lever to the specified torque. (Fig.2)
The door cannot be closed
unless the lockout key is
inserted in the slide and
turned.
The door can be opened by
supplying power to the Switch
solenoid without operating the
lockout switch.
A
Lockout key
Handle mounting screw
(TORX_T30/M6)
Inner lever
Note: The special screws are
Fig.1
Fig.1
designed so that they cannot
be turned counter-clockwise
using a flat-head
screwdriver.
Inner lever (M6)
The door cannot be closed
unless the trapped key is
inserted in the Switch and
turned.
The door can never be opened
without both supplying power
to the Switch solenoid and
operating the trapped key.
(Refer to information on the
D4JL-@@@A-@7-@@)
Tightening Torque
Trapped key
Hexagonal nut (M6)
9 to 10 N . m
Handle
Datasheet pdf - http://www.DataSheet4U.net/