D4Sl Omron, D4Sl Datasheet - Page 2

• Manufacturer Part Number: D4Sl
• Description: Safety interlock Switches
• Manufacturer: Omron

g66
g
Specifications (continued)
characteristics
Notes: 1. The above values are initial values.
*1. The degree of protection is tested using the method specified by the
standard (EN60947-5-1). Confirm that sealing properties are sufficient for
the operating conditions and environment beforehand. Although the switch
box is protected from dust, oil or water penetration, do not use the D4SL
in places where cutting chips, oil, water or chemicals may enter through
the key hole on the head, otherwise Switch damage or malfunctioning may
occur.
*2. The durability is for an ambient temperature of 5 to 35°C and an
ambient humidity of 40% to 70%. For further conditions, consult your sales
representative.
*3. Do not pass a 1 A, 125 VAC load through more than 3 circuits.
*4. These figures are minimum requirements for safe operation.
*5. These figures are based on the GS-ET-19 evaluation method.
*6. This value will vary with the switching frequency, environment, and
reliability level. Confirm that correct operation is possible with the actual
load beforehand.
Degree of protection *1
Durability *2
Operating speed
Operating frequency
Direct opening force *4
Direct opening travel *4
Holding force *5
Contact resistance
Minimum applicable load *6
Rated insulation voltage (Ui)
Rated frequency
Protection against electric shock
Pollution degree
(operating environment)
Impulse
withstand
voltage
(EN60947-5-1)
Insulation resistance
Vibration
resistance
Shock
resistance
Conditional short-circuit current
Conventional free air thermal
current (Ith)
Ambient operating temperature
Ambient operating humidity
Weight
2. The Switch contacts can be used with either standard loads or
OmrOn Scientific technOlOgieS, inc.
USA
microloads. Once the contacts have been used to switch a load,
however, thy cannot be used to switch smaller loads.
The contact surfaces will become rough once they have been
used and contact reliability for smaller loads may be reduced.
Tel. [phone]
Mechanical
Electrical
Between
terminals of
same polarity
Between
terminals
of different
polarity
Between other
terminals and
non-current
carrying
metallic parts.
Malfunction
Malfunction
Destruction
The switch has
a release key
on the back of
the switch as well.
IP67 (EN60947-5-1)
1,000,000 operations min.
150,000 operations min.
(1 A resistive load at 125 VAC) *3
0.05 to 1 m/s
5 operations/minute max.
60 N min. (EN60947-5-1)
15 mm min. (EN60947-5-1)
1,300 N min.
200 mΩ max.
1 mA resistive load at 5 VDC
(N-level reference value)
150 V (EN60947-5-1)
50/60 Hz
Class II (double insulation)
3 (EN60947-5-1)
1.5 kV
1.5 kV
2.5 kV
100 MΩ min. (at 500 VDC)
10 to 55 Hz,
0.75 mm single amplitude
100 m/s
1,000 m/s
100 A (EN60947-5-1)
2.5 A (EN60947-5-1)
-10 to +55°C (with no icing)
95% max.
Approx. 360 g (Connector model)
Approx. 390 g (Terminal Block model)
canada
2
min.
2
min.
Tel. [phone]
Two operation key holes
Can be mounted
from four directions.
The switch has an
indicator on the back
of the switch as well.
Notched side is No. 1
1
Structure
Structure
D4Sl-□□D□-D4n connector model
The switch has
a release key
on the back of
the switch as well.
D4Sl-□□D□-D4 terminal Block model
The switch has
a release key
on the back of
the switch as well.
2
For the Latest Information
On the Internet: www.sti.com
www.DataSheet.co.kr
3
4
5
6
10
Two operation key holes
Two operation key holes
Can be mounted
from four directions.
Can be mounted
from four directions.
The switch has an
indicator on the back
of the switch as well.
The switch has an
indicator on the back
of the switch as well.
D4Sl
Safety interlock Switches
Notched side is No. 1
1
1
2
The switch has
a release key
on the back of
the switch as well.
2
3
4
5
3
6
7
4
8 10
9
5
6
10
Two operatio
Datasheet pdf - http://www.DataSheet4U.net/
Can be m
from fou
The sw
indicato
of the s