VCC1 VECTRON, VCC1 Datasheet
![no-image](/images/no-image-200.jpg)
VCC1
Available stocks
Related parts for VCC1
VCC1 Summary of contents
Page 1
... Vectron’s VCC1 Crystal Oscillator (XO) is quartz stabilized square wave generator with a CMOS output, operating off either a 1.8, 2.5, 3 5.0 volt supply The VCC1 is uses fundamental or 3 crystals resulting in low jitter performance, Output typically 0.5pS rms in the 12 kHz to 20MHz Buffer / band. Also a monolithic IC, which improves ...
Page 2
... Includes calibration tolerance, operating temperature, supply voltage variations, aging and shock and vibration (not under operation). 5. Output will be enabled if enable/disable is left open 50 Time Period Figure 1. Output Waveform Vectron International 267 Lowell Rd, Hudson NH 03051 Symbol Min Typical f 0.012 O V 4 ...
Page 3
... VCC1 Data sheet Table 2. Electrical Performance, 3.3V option Parameter Frequency 1 Operating Supply Voltage Absolute Maximum Operating Voltage Supply Current, Output Enabled < 1.500 MHz 1 MHz 20. MHz 50. MHz 85.01 to 189 MHz Supply Current, Output disabled Output Logic Levels 2 Output Logic High 2 Output Logic Low ...
Page 4
... VCC1 Data sheet Table 3. Electrical Performance, 2.5V option Parameter Frequency 1 Operating Supply Voltage Absolute Maximum Voltage Supply Current, Output Enabled < 20 MHz 20. MHz 50.00 to 110 MHz 110.1 to 172 MHz Supply Current, Out disabled Output Logic Levels 2 Output Logic High 2 Output Logic Low ...
Page 5
... VCC1 Data sheet Table 4. Electrical Performance, 1.8V option Parameter Frequency 1 Operating Supply Voltage Absolute Maximum Voltage Supply Current, Output Enabled < 20 MHz 20. MHz 70. MHz 96.01 to 125 MHz 125.01 to 172 MHz Supply Current, Out disabled Output Logic Levels 2 Output Logic High 2 Output Logic Low ...
Page 6
... VCC1 Data sheet Enable/Disable Functional Description Under normal operation the Enable/Disable is left open or set to a logic high state. When the E/D is set to a logic low, the oscillator stops and the output high impedance state. This helps reduce power consumption as well as facilitating board testing and troubleshooting. ...
Page 7
... VCC1 Data sheet Figure 10, Alternate Package drawing Tape and Reel Table 5: Tape and Reel Dimensions (mm Tape Dimensions Product VCC1 12 5.5 1.5 Vectron International 267 Lowell Rd, Hudson NH 03051 Contact Pads are gold over nickel Reel Dimensions ...
Page 8
... Resistance to Solvents Handling Precautions Although ESD protection circuitry has been designed into the the VCC1, proper precautions should be taken when handling and mounting. VI employs a Human Body Model and a Charged-Device Model (CDM) for ESD susceptibility testing and design protection evaluation. ESD thresholds are dependent on the circuit parameters used to define the model ...
Page 9
... VCC1 Data Sheet Suggested IR profile Devices are built using lead free epoxy and can also be subjected to standard lead free IR reflow conditions, Table 9 shows max temperatures and lower temperatures can also be used e.g. peak temperature of 220C. Table 9. Reflow Profile (IPC/JEDEC J-STD-020B) Parameter PreHeat Time ...
Page 10
... VCC1 Data Sheet Ordering Information VCC1 - Product Family Crystal Oscillator Voltage Options A: +5.0 Vdc +/-10% , 15pF B: +3.3 Vdc +/-10%, 15pF C: +3.0 Vdc +/-10%, 15pF E: +5.0 Vdc +/-10%, 50pF F: +3.3Vdc +/-10%, 50pF G: +2.5Vdc +/-10%, 15pF H: +1.8Vdc +/-10%, 15pF Note: Not all combinations are available. Tristate with a 45/55% is the most common Electrical code and is recommended for most applications ...