PM2005P South African Micro-Electronic Systems, PM2005P Datasheet

no-image

PM2005P

Manufacturer Part Number
PM2005P
Description
Evaluation Board For The SA2005M And SA2005P Energy Metering Ic
Manufacturer
South African Micro-Electronic Systems
Datasheet
DataSheet4U.com
www.DataSheet4U.com
DataSheet
Evaluation Board for the SA2005M and SA2005P
Energy Metering IC’s
FEATURES
+
+
+
+
+
+
+
+
DESCRIPTION
The SA2005M IC is a single-chip solution with pin
programmable features. The SA2005P IC is also a single-chip
solution and retrieves its configuration and calibration
information from an external EEPROM. More detailed
information specific to the SA2005M or SA2005P can be found
in the applicable Datasheets.
The PM2005M/P evaluation board has been designed to be a
SPEC-0506 (REV.3)
PM2005M/P
4
Designed to be used as fully functional Watt-Hour meter.
Better than Class 1 operation
On-board power supply
3 Phase 4 Wire configuration
On-board current transformers
Measured energy pulse output LED
Individual phase direction indication
Individual phase fail and error condition indication
U
.com
SK1
GND
CT1
CT2
CT3
Power
Supply
Resistor
Network
Resistor
Network
Resistor
Network
GND
VSS
VDD
SA2005M
SA2005P
Figure 1: Block diagram
PH/DIR
DataSheet4U.com
MOP
MON
LED
PH3
PH2
PH1
7
8
9
1/12
fully functional watt-hour meter for three-phase four-wire
applications using either the SA2005M or SA2005P. The mains
voltages easily connect to the module by way of a Molex
connector (SK1). The 3 on-board current transformers
measure the current in each phase. A simple capacitive power
supply supplies the energy metering IC with power. The LM431
regulators are used to generate 5V supply voltage for the IC on
the board.
SA2005M specific:
+
+
SA2005P specific:
+
+
VFAIL1
0 0 0 0 0 0
Jumpers / EEPROM
Selectable calibration LED resolution and assuming
mode
Calibration and setup data stored on an external
EEPROM
Flexible programmable features
Selectable dividing ratios for different rated conditions
VDD
Module Setup
DIR1
Stepper motor
VSS
DataSheet4U.com
VFAIL2
DIR2
sames
VDD
VFAIL3
LED
DIR3
03-10-02

Related parts for PM2005P

PM2005P Summary of contents

Page 1

... The SA2005P IC is also a single-chip solution and retrieves its configuration and calibration information from an external EEPROM. More detailed information specific to the SA2005M or SA2005P can be found in the applicable Datasheets. The PM2005M/P evaluation board has been designed SK1 GND Power ...

Page 2

PM2005M/P SETTING UP THE PM2005M/P MODULE JUMPER DESCRIPTION Power Supply Jumpers The power supply jumpers are used to disconnect the on- board power supply, allowing the metering section of the circuit to be powered from an external power supply ...

Page 3

PM2005M/P CONNECTOR DESCRIPTION SK1 Connects the three phase 4 wire supply to the module. J8 (SA2005P only) Programming interface for the IIC EEPROM. Number sames PM2005M/P J8 VDD U2 VSS SCL SDA RLOAD DataSheet4U.com ...

Page 4

PM2005M/P SETTING UP THE MODULE FOR ENERGY MEASUREMENT Figure 3 below shows a typical setup for the PM2005M/P evaluation module. The three phase voltages are connected directly to SK1 and each corresponding phase current is wired through the on-board ...

Page 5

PM2005M/P CIRCUIT DESCRIPTION ANALOG SECTION The analog (metering) interface described in this section is designed for measuring 3x 230V/60A than Class 1. The most important external components for the SA2005M and SA2005P integrated circuit are the current sense resistors, ...

Page 6

PM2005M/P POWER SUPPLY Referring to figure 9, capacitor C10 is charged through D2 during the positive half of the sine wave from the R29, C12 mains voltage dropper. Identical charging circuitry exists for the other two phases. During the ...

Page 7

PM2005M/P COMPONENT LIST Items Part Type 1 1µ / 16v / No Polarity 2 220n / 63v 3 1µ / 63v 4 100n 5 10µ / 16v 6 470µ / 25V 7 470n / 250VAC 8 470µ / 16V ...

Page 8

PM2005M/P PCB LAYOUT DataSheet4U.com http://www.sames.co.za 4 DataSheet U .com DataSheet4U.com Figure 6: PM2005M Top PCB layout Figure 7: PM2005M Bottom PCB layout 8/12 DataSheet4U.com sames ...

Page 9

PM2005M/P DataSheet4U.com http://www.sames.co.za 4 DataSheet U .com CT3 CT2 PM2005M/P.PCB Phase 3 Calibrate Phase 3 Calibrate R11 R12 Phase 2 Calibrate Phase 2 Calibrate PM2005M/P R10 R2 SA2005P R6 R8 S10 ...

Page 10

PM2005M/P DataSheet4U.com http://www.sames.co.za 4 DataSheet U .com DataSheet4U.com Figure 9: Schematic Diagram for Metering Section 10/12 sames DataSheet4U.com ...

Page 11

PM2005M/P DataSheet4U.com http://www.sames.co.za 4 DataSheet U .com DataSheet4U.com Figure 10: Schematic Diagram of Power Supply 11/12 sames DataSheet4U.com ...

Page 12

... PM2005M/P DISCLAIMER: The information contained in this document is confidential and proprietary to South African Micro-Electronic Systems (Pty) Ltd ("SAMES") and may not be copied or disclosed to a third party, in whole or in part, without the express written consent of SAMES. The information contained herein is current as of the date of publication; however, delivery of this document shall not under any circumstances create any implication that the information contained herein is correct as of any time subsequent to such date ...

Related keywords