IL600A NVE Corp., IL600A Datasheet
IL600A
Related parts for IL600A
IL600A Summary of contents
Page 1
... Space-critical multi-channel applications • Isolated Relays and Actuators Description The IL600A-Series are isolated signal couplers with open- drain outputs. They have a similar interface but better performance and higher package density than optocouplers. The devices are manufactured with NVE’s patented* ® ...
Page 2
... V CM Symbol Min. Typ. 3.01 4.03 7.08 9 0.2 14 >10 ||7 V 1000 ISO V 2500 ISO N1502812, N1502812-101 Package Pollution Degree PDIP II SOIC (0.15" IL600A Series Max. Units Test Conditions 150 °C 125 ° +1 HBM Max. Units Test Conditions 85 ° ...
Page 3
... Data out, channel GND Ground return for V 1 DD1 5 GND Ground return for V 2 DD2 6 IN Data in, channel Supply Voltage 2 DD2 8 OUT Data out, channel 1 1 IL600A Series NC IN+ IN- NC IL610A IL611A DD1 OUT ...
Page 4
... I FS-HIGH I 8 FS-LOW Switching Specifications at 3.3V Symbol Min. Typ 100 t PHL t PLH |CM |,| −25 I FS-HIGH 4 IL600A Series Max. Units Test Conditions T μ||nH AMB V Ω/°C 0.25 V Single or Differential Single or Differential pullup ...
Page 5
... To calculate the value of the protection resistor (R1), use Ohm’s law as shown in the examples below. Note that only the magnitude of the voltage across the coil is important; the absolute values 10nF R limit 15pF 2 Test Circuit 2 (Differential) 5 IL600A Series + IL610A ...
Page 6
... V or 3.3 V output supplies. The specifications on pages 5 and 6 show the enhanced failsafe conditions available with the IL600A-Series Isolators that cover the non-open circuit condition. The output will remain in the state specified, or will switch to that state, if the specified current is flowing in the coil. Note that positive values of current mean current flow into the In− input (pin 3 in Test Circuit 1) ...
Page 7
... Figure guide to boost capacitor selection. For standard logic signals (t recommended. The capacitor value is generally not critical, and can often vary ±50% with little noticeable difference in device performance. 5000 5000 7 IL600A Series ,t < capacitor ...
Page 8
... The stated direction of the current is negative in Figure 4 because the magnetic field is negative with respect to Earth Field. Current is always fed into the In− terminal of an IL600A-Series device. Since these currents are actually sourced, not sunk, by the user, the specified currents are quoted as positive values in the Electrical Specifications section of this data sheet. ...
Page 9
... boost boost IL610A IL610A Data In Data In GND GND 1 1 Non-Inverting Circuit Non-Inverting Circuit Figure 5. Inverting and Non-Inverting circuits 9 IL600A Series Data Out Data Out GND GND 2 2 Note. C Note ...
Page 10
... Gauss 1 cm from the device could cause disturbance current of 200 A flowing in a conductor ±250 Gauss 1 cm from the device could cause disturbance. μ s long are more susceptible to magnetic fields than shorter pulse widths. 10 IL600A Series OUT ...
Page 11
... CMOS-output IL600-Series Isolators) are needed as well as possibly better impedance matching. 8 IL610A boost GND is application specific 2 2 boost Number of Current Limit Nodes Resistors (Ω) 1 None IL600A Series V DD2 R ...
Page 12
... Multi-channel Isolated Alarm Monitor The open-drain outputs of IL600A-Series Isolators allow wired-OR outputs. The inputs can be configured for inverting or non- inverting operation (see Applications Information), and a very wide input voltage range is possible. This illustrative circuit provides fail-safe output (logic high output for zero coil current) and typical logic output sink current for each isolator. ...
Page 13
... This circuit provides bidirectional data transfer 10K 8 270 DD1 750R DD2 IL612A GND 1 Notes: C1, C2, and C3 are 47nF ceramic Resistor values change for 3 V operation 2 C-bus signals. 13 IL600A Series 5V 750R SDA_iso 750R GND 2 ...
Page 14
... Dimensions in inches (mm) 0º 8º 0.016 (0.40) 0.050 (1.27) 0.010 (0.25) 0.020 (0.50) x45º 0.008 (0.19) 0.010 (0.25) 0.29 (6.4) 0.31 (7.9) 0.008 (0.2) 0.015 (0.4) 0.30 (7.6) 0.37 (9.4) 14 IL600A Series 0.054 (1.37) 0.069 (1.75) 0.004 (0.10) 0.040 (1.0) 0.010 (0.25) 0.060 (1.5) NOTE: Pin spacing is a BASIC dimension; tolerances do not accumulate 0.030 (0.76) 0.09 (2.3) 0.045 (1.14) 0.11 (2.8) 0.015 (0.38) NOTE: Pin spacing is a BASIC ...
Page 15
... Output Type Blank = CMOS Output A = Open Drain Output Base Part Number 610 = Single Channel 611 = 2 Transmit Channels 612 = 1 Transmit Channel, 1 Receive Channel Product Family IL = Isolators 15 IL600A Series IL610A Valid Part Numbers IL610A-1E IL610A-2E IL610A-3E IL610A-5 IL610A-1ETR7 IL610A-3ETR7 IL610A-1ETR13 IL610A-3ETR13 IL611A Valid ...
Page 16
... Application circuits changed to show C • Figure Four shows C . BOOST • Test Circuit #2 removed Changes • Test circuits added. • Boost capacitor selector added • Note on 3.3 V supplies the boost capacitor must be used • Input threshold current for logic low changed to 0.5 mA. 16 IL600A Series BOOST ...
Page 17
... No license is granted by implication, or otherwise, under any patent or patent rights of NVE Corporation. NVE Corporation does not authorize, nor warrant, any NVE Corporation product for use in life support devices or systems or other critical applications, without the express written approval of the President of NVE Corporation. Specifications are subject to change without notice. ISB-DS-001-IL600A-M February 2008 IL600A Series 17 ...