MCT0603HF Vishay, MCT0603HF Datasheet - Page 5

• Manufacturer Part Number: MCT0603HF
• Description: High Frequency Flat Chip Resistors
• Manufacturer: Vishay

TESTS AND REQUIREMENTS
All tests are carried out in accordance with the following
specifications:
EN 60115-1, Generic specification (includes tests)
EN 140 400, Sectional specification (includes schedule for
qualification approval)
EN 140 401-801, Detail specification (includes schedule for
conformance inspection)
The components are approved in accordance with the
European CECC-system, where applicable. The following
table contains only the most important tests. For the full test
schedule refer to the documents listed above. The testing
also covers most of the requirements specified by
EIA/IS-703 and JIS-C-5202.
The tests are carried out in accordance with IEC 60068 and
under standard atmospheric conditions in accordance with
IEC 60068-1, 5.3. Climatic category LCT/UCT/56 (rated
Document Number: 28712
Revision: 25-Aug-08
TEST PROCEDURES AND REQUIREMENTS
4.5
4.8.4.2
4.25.1
4.25.3
4.24
4.23
4.23.2
4.23.3
4.23.4
4.23.5
4.23.6
-
4.19
4.13
EN 60115-1
CLAUSE
IEC 60068-2 TEST
METHOD
78 (Cab)
30 (Db)
30 (Db)
14 (Na)
13 (M)
2 (Ba)
1 (Aa)
1 (Aa)
-
-
-
-
-
For technical questions, contact: [e-mail]
Standard operation mode
Damp heat, steady state
standard operation mode
Temperature coefficient
category temperature
Endurance at 70 °C:
Short time overload;
Endurance at upper
Climatic sequence:
Damp heat, cyclic
Damp heat, cyclic
Low air pressure
Rapid change of
temperature
Resistance
High Frequency Flat Chip Resistors
Dry heat
TEST
Cold
Cold
55 °C; 24 h; > 90 % RH; 1 cycle
Stability for product types:
U =
8.5 kPa; 2 h; 25 ± 10 °C
> 95 % to 100 % RH;
(40 ± 2) °C; 56 days;
At 20/- 55/20 °C and
U = 2.5 x
30 min at LCT and
temperature range: Lower Category Temperature, Upper
Category Temperature; damp heat, long term, 56 days) is
valid.
Unless otherwise specified the following values apply:
Temperature: 15 °C to 35 °C
Relative humidity: 45 % to 75 %
Air pressure: 86 kPa to 106 kPa (860 mbar to 1060 mbar).
The components are mounted for testing on boards in
accordance with EN 60115-1, 4.31 unless otherwise
specified.
The requirements stated in the Test Procedures and
Requirements table below are based on the required tests
and permitted limits of EN 140 401-801. However, some
additional tests and a number of improvements against those
minimum requirements have been included.
125 °C; 1000 h
30 min at UCT;
UCT = 125 °C;
(93 ± 3) % RH
LCT = - 55 °C;
LCT = - 55 °C;
55 °C; 5 days;
UCT = 125 °C
70 °C; 1000 h
70 °C; 8000 h
PROCEDURE
20/125/20 °C
P
- 55 °C; 2 h
UCT; 16 h
70
LCT; 2 h
0.5 h off
5 cycles
5 cycles
x R
MCT 0603 HF
P
70
1.5 h on;
x R
REQUIREMENTS PERMISSIBLE
Vishay Beyschlag
± (0.5 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
± (0.5 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
± (1 % R + 0.05 Ω)
no visible damage
CHANGE (ΔR/R)
MCT 0603 HF
6.8 Ω to 470 Ω
± 50 ppm/K
± 2 %
www.vishay.com
5