LSM-16A C&D Technologies., LSM-16A Datasheet
LSM-16A
Related parts for LSM-16A
LSM-16A Summary of contents
Page 1
... CURRENT SENSE PWM CONTROLLER Figure 1. Simplified Schematic www.murata-ps.com LSM-16A D12 Models Non-Isolated, 13-80W SMT DC/DC Converters Typical Unit Non-Isolated, 12V , 0.75-5V in noise (50mVp-p typ.), tight line/load regulation (±0.1%/±0.25% max.), quick step response (100µsec), stable no-load operation, and no output reverse conduction. The fully functional LSM’ ...
Page 2
... Nominal line voltage, no-load/full-load conditions. Mechanical Specifications - C RoHS-6 compliant* D12 = Volts (12V nominal) * Contact MPS for availability. 0.60 (15.24) NOTCH IN SHELL INDICATES PIN ONE NOTCH IN SHELL INDICATES PIN ONE www.murata-ps.com LSM-16A D12 Models Input Efficiency (Full Load nom min in in Range I ➃ in (Volts) (mA/A) Min ...
Page 3
... DC/DCs requires that the dc input voltage source have low ac impedance at the frequencies of interest. Highly inductive source imped- ances can greatly affect system stability. Your specific system configuration may necessitate additional considerations. www.murata-ps.com LSM-16A D12 Models Non-Isolated, 13-80W SMT DC/DC Converters a Absolute Maximum Ratings 15 Volts ...
Page 4
... LSM's specified rating. Therefore: (V www.murata-ps.com LSM-16A D12 Models Non-Isolated, 13-80W SMT DC/DC Converters Start-Up Time is the interval between the time at which a ramp- OUT Start-Up Time assumes the converter is turned off via the OUT (+) – ...
Page 5
... Trim pin and Common to trim up the output voltage. Fixed resistors should have absolute TCR’s less than 100ppm/°C to ensure stability. www.murata-ps.com LSM-16A D12 Models Non-Isolated, 13-80W SMT DC/DC Converters Figure 6. Trim Connections Using a Trimpot Technical enquiries email: sales@murata-ps.com, tel: MDC_LSM 16A D12 Models ...
Page 6
... The equation for this voltage adjustment is: The LSM-T/16-D12 fixed trim voltages to set the output voltage are (V) t www.murata-ps.com LSM-16A D12 Models Non-Isolated, 13-80W SMT DC/DC Converters 10500 – 1000 ( ) = V – 0.7525 O is the desired output voltage. o ...
Page 7
... If you are attempting to extract the most current out of these units under demanding temperature conditions, we advise you to monitor the output- inductor temperature to ensure it remains below +110°C at all times. www.murata-ps.com LSM-16A D12 Models Non-Isolated, 13-80W SMT DC/DC Converters R losses. The derating curves were 2 Technical enquiries email: sales@murata-ps ...
Page 8
... Efficiency vs. Line Voltage and Load Current @ 25° 10V 12V 14V Load Current (Amps) www.murata-ps.com Non-Isolated, 13-80W SMT DC/DC Converters LSM-16A D12 Models Technical enquiries email: sales@murata-ps.com, tel: +1 508 339 3000 MDC_LSM 16A D12 Models.A03 Page ...
Page 9
... Typical Performance Curves for LSM D12 SMT Series www.murata-ps.com LSM-16A D12 Models Non-Isolated, 13-80W SMT DC/DC Converters Technical enquiries email: sales@murata-ps.com, tel: MDC_LSM 16A D12 Models.A03 Page 508 339 3000 ...
Page 10
... Typical Performance Curves for LSM D12 SMT Series www.murata-ps.com LSM-16A D12 Models Non-Isolated, 13-80W SMT DC/DC Converters Technical enquiries email: sales@murata-ps.com, tel: MDC_LSM 16A D12 Models.A03 Page 508 339 3000 ...
Page 11
... PCB TEMPERATURE INSIDE THE HEAT SHIELD 150 200 250 Time (Seconds) Figure 6. Reflow Solder Profile www.murata-ps.com LSM-16A D12 Models Non-Isolated, 13-80W SMT DC/DC Converters HEAT SHIELD OUTSIDE TEMPERATURE 300 350 Technical enquiries email: sales@murata-ps.com, tel: MDC_LSM 16A D12 Models.A03 Page ...
Page 12
... Figure 7. Tape Dimensions USA: Tucson (AZ), Tel: (800) 547 2537, email: sales@murata-ps.com Canada: UK: France: Germany: München, Tel: +49 (0)89-544334-0, email: ped.munich@murata-ps.com Japan: China: 3/3/08 www.murata-ps.com LSM-16A D12 Models Non-Isolated, 13-80W SMT DC/DC Converters CENTERED PICK UP LOCATION NOTCH IN SHELL INDICATES PIN ONE. FEED DIRECTION TAPE 13 ...