PR3-TS-24AC-F100-60 Willow Technologies Ltd, PR3-TS-24AC-F100-60 Datasheet

PR3-TS-24AC-F100-60

Manufacturer Part Number

PR3-TS-24AC-F100-60

Description

Ac & Dc Solenoids

Manufacturer

Willow Technologies Ltd

Datasheet

1.PR3-TS-24AC-F100-60.pdf (3 pages)

Current page: 1 of 3
Download datasheet (291Kb)

AC & DC Solenoids

Open frame linear solenoids designed for

AC & DC applications. Both the frame and

the plunger are made of solid steel

construction. They can be operated in any

position, turning an electric pulse into an

axial pull or push-pull action. Coil winding

insulation being in Class F. Performance,

as shown in the following diagrams, is

always referred to a temperature rise of

80°C in open air, with 35°C ambient

temperature and coil fed at 105% of rated

voltage (VDE 0580). Since the mechanical

energy generated by all solenoids is a

constant, any amount of

ON and OFF times corresponding to

relative duty factors lower than ED=100

result, for standard ED values, from the

following diagram:

Current values given in our diagrams are

at nominal voltage. Forces shown are

referred to solenoids fed @ 90% of rated

voltage, with ‘hot’ coil at 20°C ambient

temperature.

Any AC solenoid, due to its high power

consumption (VA), will rapidly overheat

and fail to operate, whenever its plunger is

prevented from seating properly. To avoid

this, a proper spring can be interposed

between plunger and application. DC

solenoids are not affected by this problem,

as current consumed is constant all along

the plunger run. When adopting a solenoid

please also bear in mind what follows:

1) Any load should be always applied

strictly along the plunger main axis (to

avoid excessive wear due to friction, and

noise

ORDERING IMFORMATION

PR3-TS-24AC-F100-60

1 2

magnifying due to the vibration

ITALIANA

RELE

Tel (+39) 02 6140851- Fax (+39) 02 6140339 - E-mail: rele@rele.it - www.rele.it

I T A L I A N A R E L E' S r l. - Via dei Bravi, 40

that

force

SERIES PR

eventually

application will be expended under form

application

smallest available solenoid performing the

required action, whilst not exceeding the

max admitted operational temperature. To

select the right solenoid, also the exact

determination of the duty cycle is equally

essential: in fact, whenever the maximum

cycle is exceeding 300 seconds, a

continuously rated solenoid (ED=100)

must be used. Otherwise the relative duty

factor would result as follows:

generated by the AC power supply).

2) Any mechanical stroke-limiting device

eventually provided, should be made of

non magnetic material.

3) The expected life of a solenoid would

be remarkably increased as much as its

impact force could be absorbed by the

solenoid mounting frame.

When a continuously rated (ED=100)

solenoid is required but space is not

enough, a ballast resistor and/or a limiting

impedance could be used to feed a

smaller

(ED<100).

1 - Solenoid series: PR

2 - Type (size): 1-2-3-4

3 - Action: T = Pull (standard)

4 - Coil supply voltage: AC or DC

5 - Coil terminals:

F = Faston 0.25 (6.3x0,8mm)

C = 150 mm leads (PR1 = 100 mm)

impact

Operation

per hour

(not available for PR1)

1200

1800

3000

TS = Push-pull

120

300

600

intermittently

not

should

force.

utilised

Total cycle

(seconds)

Consequently,

correctly

300

1.2

rated

RELATIVE DUTY FACTOR (ED%)

0.48 0.72

120

use

4.8

2.4

1.2

0.8

solenoid

relevant

I-20032 CORMANO - Italy

ED 40

OFF

any

180

7.2

3.6

1.8

1.2

the

ED% =

(Cycle = ON + OFF time)

Prior to select the right solenoid you

must always know the force required, as

well as stroke, maximum feeding time,

minimum OFF time, ambient temperature

and supply voltage. If in doubt to select

the best type for your application, please

do not hesitate contacting us to help you

making the right choice, supplying us with

all above information. Even if you can’t

find the solenoid you require in our range,

please let us know, as we do have both

the experience and the ability to solve any

problem in this field.

6 - Relative duty service ED%:

7 - Coil supply frequency (if differing

NB: When ordering standard types

you can omit the last group of code (7).

0.75

7.5

3.0

1.5

0.5

0.3

ED 25

Permanently (100) or intermittently

rated coils (standard values: 40-25-

15-5)

from 50 Hz).

225

22.5

OFF

9.0

4.5

2.25

1.5

0.9

(On + OFF time)

ON time

0.45

0.18

4.5

1.8

0.9

0.3

ED 15

255

25.5

10.2

OFF

5.1

2.55

1.7

1.02

x 100

0.15

0.06

1.5

0.6

0.3

0.1

ED 5

285

28.5

11.4

OFF

5.7

2.85

1.9

1.14

Related parts for PR3-TS-24AC-F100-60

PR3-TS-24AC-F100-60 Summary of contents

Page 1

... Any load should be always applied strictly along the plunger main axis (to avoid excessive wear due to friction, and noise magnifying due to the vibration ORDERING IMFORMATION PR3-TS-24AC-F100- Via dei Bravi, 40 Tel (+39) 02 6140851- Fax (+39) 02 6140339 - E-mail: rele@rele ...

Page 2

... AC 1250 1050 950 700 350 - DC 5 1250 1000 900 800 650 300 AC PR3 Coil supply voltages : Insulating resistance : Dielectric strength : Coil terminals : Total / Plunger weight : Axial Force (grams) Vs. Stroke and Duty Factor (ED 200 ...

Page 3

Via dei Bravi, 40 Tel (+39) 02 6140851- Fax (+39) 02 6140339 - E-mail: rele@rele.it - www.rele.it I-20032 CORMANO - Italy ...

Related keywords

PR3-TS-24AC-F100-60 datasheet
PR3-TS-24AC-F100-60 data sheet
PR3-TS-24AC-F100-60 pdf datasheet
PR3-TS-24AC-F100-60 component
PR3-TS-24AC-F100-60 part
PR3-TS-24AC-F100-60 distributor
PR3-TS-24AC-F100-60 RoHS
PR3-TS-24AC-F100-60 datasheet download