Z4K260-RE-10 Superworld Electronics, Z4K260-RE-10 Datasheet
Z4K260-RE-10
Related parts for Z4K260-RE-10
Z4K260-RE-10 Summary of contents
Page 1
... Storage temp. : -55°C to +125°C d) Operating temp. : -55°C to +125°C e) Resistance to solder heat : 260°C.10secs NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD (a) Series code (b) Dimension code (c) Material code (d) Impedance code : 260 = 26 ...
Page 2
... FERRITE CHIP BEADS 6. ELECTRICAL CHARACTERISTICS : EIA Part Number Size Z4K260-RE-10 1206 Z4K310-RE-10 1206 Z4K420-RE-10 1206 Z4K500-RE-10 1206 Z4K700-RE-10 1206 Z4K900-RE-10 1206 Z4N190-RE-10 1206 7. IMPEDANCE VS. FREQUENCY CURVES : Z4K260-RE-1 0 Z4K260-RE-00 F CB3 21 6K-260 T05 UEN C Y Z4K420-RE-1 0 Z4K 420-R E-00 ...
Page 3
... FR EQU ENC Y(M Hz) Z4N1 90-RE 4N190-RE-00 FCB 321 6N -190T REQ UEN C Y(M Hz) NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD 200 160 120 100 1000 100 1000 ...
Page 4
... Flexture Strength The terminal electrode & the dielectric must not be damaged by the forces applied on the right conditions. NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD PERFORMANCE Preheating Dipping Natural cooling 260° ...
Page 5
... For the detail derating of current, please refer to the Derated Current vs. Operating Temperature curve. NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD PERFORMANCE 1.0(0.039) R0.5(0.02) ...
Page 6
... Time(sec.) Figure 1. Re-flow Soldering NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD PC board should be designed so that products are not sufficient under mechanical stress as warping the board. Products shall be positioned in the sideway direction against the mechanical stress to prevent failure ...
Page 7
... Accordingly increasing the solder volume, the mechanical stress to product is also increased. Exceeding solder volume may cause the failure of mechanical or electrical performance. Solder shall be used not to be exceed as shown in Fig. 4. NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD Z4 SERIES Upper limit ...
Page 8
... Material : Plastic D:1.5+0.1 Po:4±0.1 P2:2±0. D1:1±0.1 10-2.1 Tape Dimension / 12mm Po:4±0.1 P2:2±0.05 D:1.5+0 D1:1.5±0.1 NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD 2±0.5 7" x 12mm R1.9 t Series Size 3(09 Series Size 3(09 3(12 ...
Page 9
... Products should be handled with care to avoid damage or contamination from perspiration and skin oils. b) The use of tweezers or vacuum pick up is strongly recommended for individual components. c) Bulk handling should ensure that abrasion and mechanical shock are minimized. NOTE : Specifications subject to change without notice. Please check our website for latest information. SUPERWORLD ELECTRONICS (S) PTE LTD ...