ICL3245 Intersil Corporation, ICL3245 Datasheet - Page 11

no-image

ICL3245

Manufacturer Part Number
ICL3245
Description
1ma, +3v To +5.5v, 1mbps, Rs-232 Transceivers With Enhanced Automatic Powerdown
Manufacturer
Intersil Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ICL3245CA
Manufacturer:
NS
Quantity:
2
Part Number:
ICL3245CA
Manufacturer:
ICS
Quantity:
240
Part Number:
ICL3245CA
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ICL3245CA-T
Manufacturer:
INTERSIL
Quantity:
14 107
Part Number:
ICL3245CB
Manufacturer:
HARRIS
Quantity:
20 000
Part Number:
ICL3245ECA
Manufacturer:
NS
Quantity:
1
Part Number:
ICL3245ECA
Manufacturer:
Intersil
Quantity:
105
Part Number:
ICL3245ECAZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ICL3245ECVZ
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ICL3245EIAZ
Manufacturer:
INTERSIL
Quantity:
20 000
receiver and transmitter inputs. Detaching the cable allows
the receiver inputs to drop to an invalid level (GND), so
INVALID switches low and forces the RS-232 device to
power down. The ICL32XX remains powered down until the
cable is reconnected (INVALID = FORCEOFF = 1) and a
transition occurs on a receiver or transmitter input (see
Figure 7). For immediate power up when the cable is
reattached, connect FORCEON to FORCEOFF through a
network similar to that shown in Figure 5.
Ready Output (ICL3225 Only)
The Ready output indicates that the ICL322X is ready to
transmit. Ready switches low whenever the device enters
powerdown, and switches back high during power-up when
V- reaches -4V or lower.
Capacitor Selection
The charge pumps require 0.1µF capacitors for 3.3V
operation. For other supply voltages refer to Table 3 for
capacitor values. Do not use values smaller than those listed
in Table 3. Increasing the capacitor values (by a factor of 2)
reduces ripple on the transmitter outputs and slightly
reduces power consumption. C
increased without increasing C
increase C
maintain the proper ratios (C
When using minimum required capacitor values, make sure
that capacitor values do not degrade excessively with
temperature. If in doubt, use capacitors with a larger nominal
value. The capacitor’s equivalent series resistance (ESR)
usually rises at low temperatures and it influences the
amount of ripple on V+ and V-.
Power Supply Decoupling
In most circumstances a 0.1µF bypass capacitor is
adequate. In applications that are particularly sensitive to
power supply noise, decouple V
capacitor of the same value as the charge-pump capacitor C
Connect the bypass capacitor as close as possible to the IC.
Operation Down to 2.7V
ICL32XXE transmitter outputs meet RS-562 levels (
at full data rate, with V
typically ensure inter operability with RS-232 devices.
3.0 to 3.6
4.5 to 5.5
3.0 to 5.5
V
CC
TABLE 3. REQUIRED CAPACITOR VALUES
1
(V)
without also increasing C
CC
as low as 2.7V. RS-562 levels
C
0.047
1
1
11
0.1
0.1
(µF)
to the other capacitors).
1
2
CC
’s value, however, do not
, C
3
to ground with a
, and C
2
, C
3
C
, and C
4
2
, C
can be
3
0.33
0.47
0.1
, C
4
4
±
to
ICL3225, ICL3245
3.7V),
(µF)
1
.
Transmitter Outputs when Exiting
Powerdown
Figure 10 shows the response of two transmitter outputs
when exiting powerdown mode. As they activate, the two
transmitter outputs properly go to opposite RS-232 levels,
with no glitching, ringing, nor undesirable transients. Each
transmitter is loaded with 3kΩ in parallel with 2500pF. Note
that the transmitters enable only when the magnitude of the
supplies exceed approximately 3V.
Mouse Driveability
The ICL3245 is specifically designed to power a serial mouse
while operating from low voltage supplies. Figure 11 shows the
transmitter output voltages under increasing load current. The
on-chip switching regulator ensures the transmitters will supply
at least
V+ transmitters, 7.3mA for single V- transmitter).
5V/DIV.
2V/DIV
FIGURE 11. TRANSMITTER OUTPUT VOLTAGE vs LOAD
FIGURE 10. TRANSMITTER OUTPUTS WHEN EXITING
5V/DIV.
-1
-2
-3
-4
-5
-6
6
5
4
3
2
1
0
0
±
5V during worst case conditions (15mA for paralleled
V
CC
1
CURRENT (PER TRANSMITTER, i.e., DOUBLE
CURRENT AXIS FOR TOTAL V
POWERDOWN
FORCEOFF
LOAD CURRENT PER TRANSMITTER (mA)
V
T1
T2
T3
CC
2
= 3.0V
READY
3
V
ICL3245
V
OUT
OUT
TIME (20µs/DIV.)
4
+
-
5
6
OUT+
7
V
C1 - C4 = 0.1µF
V
V
CC
OUT
OUT
8
February 27, 2006
CURRENT)
= +3.3V
+
-
T2
T1
9
FN4878.8
10

Related parts for ICL3245