TISP3600F3 Bourns, Inc., TISP3600F3 Datasheet
TISP3600F3
Related parts for TISP3600F3
TISP3600F3 Summary of contents
Page 1
... In the 3-point mode, the G terminal is connected to the system protective ground and the R and T terminals are connected to the two conductors being protected. For the TISP3600F3, each conductor will have its volt- age limited to ±600 V from the protective ground. The maximum inter-conductor voltage will be limited to ±1200 V. ...
Page 2
... TISP3600F3, TISP3700F3 Absolute Maximum Ratings °C (Unless Otherwise Noted) A Repetitive peak off-state voltage, (R-G or T-G value) Non-repetitive peak on-state pulse current (see Notes 1 and 2) 2/10 (Telcordia GR-1089-CORE, 2/10 voltage wave shape) 1/20 (I TU-T K.22, 1.2/50 voltage wave shape, 25 Ω resistor) 8/ 61000-4-5, combination wave generator, 1.2/50 voltage wave shape) 10/160 (F CC Part 68, 10/160 voltage wave shape) 4/250 (I TU-T K ...
Page 3
... TISP3600F3, TISP3700F3 Electrical Characteristics for the T and R Terminals, T Parameter C Off-state capacitance f = 100 kHz, V off NOTE 3: These capacitance measurements employ a three terminal capacitance bridge incorporating a guard circuit. The third terminal is connected to the guard terminal of the bridge. Electrical Characteristics for the T and G or the R and G Terminals, T ...
Page 4
... TISP3600F3, TISP3700F3 Parameter Measurement Information -v I (BO) V Quadrant III Switching Characteristic Figure 1. Voltage-Current Characteristic for R-G and T-G Terminal Pairs V DRM -v I DRM I (BO) V (BO) Quadrant III Switching Characteristic Figure 2. Voltage-Current Characteristic for R-T Terminal Pair +i I TSP I TSM DRM ...
Page 5
... TISP3600F3, TISP3700F3 Typical Characteristics OFF-STATE CURRENT vs JUNCTION TEMPERATURE 100 0·1 0·01 0·001 - Junction Temperature - °C J Figure 3. NOVEMBER 1997 - REVISED JANUARY 2007 Specifications are subject to change without notice. Customers should verify actual device performance in their specific applications. ...
Page 6
... TISP3600F3, TISP3700F3 Thermal Information NON-REPETITIVE PEAK ON-STATE CURRENT 1.5 vs CURRENT DURATION V = 1500 V rms, 50/60 Hz GEN R = 1.4*V /I GEN GEN TSM(t) EIA/JESD51-2 ENVIRONMENT EIA/JESD51-3 PCB SIMULTANEOUS OPERATION AND T TERMINALS TERMINAL CURRENT = 2xI 0· 100 t - Current Duration - s Figure 6 ...
Page 7
... TISP4xxx protector plus the diode forward recovery voltage. Steering diodes D7 and D8 and high-voltage protector Th2 limit the conductor voltage to ground. The limiting voltage is set by the choice of protector, TISP3600F3, 1200 V or TISP3700F3, 1400 V, and the number connected in series (one extra protector Th3 shown dotted). ...
Page 8
... MΩ insulation resistance minimum requirement measured at 500 V d.c. (250 µA maximum). In Figure 8, at least one protection element of a TISP3700F3 must be used to give the 500 V working voltage (V tion resistance requirement. To avoid breakover during the 2.4 kV impulse test, five TISP3700F3 protection elements (2 packages) or six TISP3600F3 elements (2. 0.3/50 common-mode impulse. A TISP3700F3 ( the impulse. ...
Page 9
... TISP3600F3, TISP3700F3 Device Symbolization Code Devices will be coded as follows: “TISP” trademark of Bourns, Ltd., a Bourns Company, and is Registered in U.S. Patent and Trademark Office. “Bourns” registered trademark of Bourns, Inc. in the U.S. and other countries. NOVEMBER 1997 - REVISED JANUARY 2007 Specifications are subject to change without notice. ...