MD54-0003 Tyco Electronics, MD54-0003 Datasheet - Page 2

• Manufacturer Part Number: MD54-0003
• Description: Mmic Medium Level Mixer 1700 - 2000 Mhz
• Manufacturer: Tyco Electronics

2
M/A-COM Inc. and its affiliates reserve the right to make changes to the
product(s) or information contained herein without notice. M/A-COM makes
no warranty, representation or guarantee regarding the suitability of its
products for any particular purpose, nor does M/A-COM assume any liability
whatsoever arising out of the use or application of any product(s) or
information.
MMIC Medium Level Mixer
1700 - 2000 MHz
Absolute Maximum Ratings
Handling Procedures
Please observe the following precautions to avoid
damage:
Static Sensitivity
Gallium Arsenide Integrated Circuits are sensitive
to electrostatic discharge (ESD) and can be
damaged by static electricity. Proper ESD control
techniques should be used when handling these
devices.
Electrical Specifications:
Test Conditions: RF = 1850 MHz (-10 dBm), LO = 1710 MHz (13 dBm), IF = 140 MHz, T
1. IMR vs RF drive level can be calculated by the formula: IMR = 50 - (1.5 x P
2. Exceeding any one or combination of these limits may cause
3. Total power for RF and LO ports should not exceed +23
permanent damage to this
dBm.
Input 1 dB Compression
Operating Temperature
Two-Tone IM Ratio
Storage Temperature
Conversion Loss
LO Drive Power
RF Input Power
Parameter
Parameter
Isolation
VSWR
3
1
3
device.
Absolute Maximum
-65°C to +150°C
Tone spacing 100 kHz, IF = 140 MHz
2
RF Freq. = 1800 MHz, LO = +13 dBm
-40°C to +85°C
+22 dBm
+23 dBm
Two tones at –10 dBm each,
Test Conditions
LO to RF
LO to IF
RF to IF
LO Port
RF Port
IF Port
—
• North America Tel: [phone] / Fax: [phone]
• Europe Tel: [phone] / Fax: [phone]
• Asia/Pacific Tel: [phone] / Fax: [phone]
Visit www.macom.com for additional data sheets and product information.
Spurious Table
The spurious table shows the spurious signals resulting from the
mixing of the RF and LO input signals, assuming down
conversion. Mixing products are indicated by the number of dB
below the conversion loss. The lower frequency mixing term is
shown for two different RF input levels. The top number is for an
RF input power of -5 dBm, the lower number is for -15 dBm.
|mF
|mF
RF Frequency = 1850 MHz
LO Frequency = 1710 MHz
IN
RF
RF
)
- nF
- nF
4x
3x
2x
1x
0x
LO
LO
|, RF = -5 dBm
|, RF = -15 dBm
Units
Ratio
Ratio
Ratio
dBm
dBc
-18.8
-13.1
-23.1
dB
dB
dB
dB
10.3
-8.8
6.9
0.3
0x
17
X
X
Harmonic of RF
48.2
47.2
28.9
28.9
25.7
25.9
2.1
2.1
1x
0
0
Min
—
20
—
—
—
—
—
—
50
62.3
61.1
63.0
61.3
52.1
61.3
67.5
61.1
56.8
61.7
2x
2.5:1
2.0:1
2.0:1
Typ
+21
8.5
27
12
10
65
MD54-0003
A
71.7
61.7
71.3
63.5
71.5
61.5
71.3
61.9
72.3
62.3
3x
= +25°C
Max
9.5
—
—
—
—
—
—
—
—
73.4
63.4
70.6
61.6
72.1
62.1
72.6
62.6
69.3
59.8
4x
V4