LX8816 Microsemi Corporation, LX8816 Datasheet - Page 6
![no-image](/images/manufacturer_photos/0/4/446/microsemi_corporation_sml.jpg)
LX8816
Manufacturer Part Number
LX8816
Description
Dual Channel 1a Low Dropout Regulator
Manufacturer
Microsemi Corporation
Datasheet
1.LX8816.pdf
(9 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LX8816-02
Manufacturer:
LNFINITY
Quantity:
41
Part Number:
LX8816-04
Manufacturer:
MICROSEMI/美高森美
Quantity:
20 000
Company:
Part Number:
LX8816-04CDF
Manufacturer:
MICROSEMI
Quantity:
15 932
Company:
Part Number:
LX8816-33
Manufacturer:
LNFINITY
Quantity:
13
Copyright © 2000
Rev. 1.2c, 2005-05-18
Description
The LX8816 is part of a family of Dual LDO (Low Drop-Out) linear
regulators in Microsemi’s S-PAK power package, which offer
maximum power dissipation in a low profile surface mount
technology. The family includes combination fixed and adjustable
versions. Each channel can supply up to one amp independently with a
regulator design optimized for system efficiency by consuming
minimal ground current and directing quiescent current to the load.
Input Capacitor
To improve load transient response and noise rejection a input bypass
capacitor is of at least 2.2uF is required. Generally we recommend a
20uF ceramic or tantalum or 22uF electrolytic capacitor.
Output Capacitor
The regulator requires output capacitors connected between V
GND to stabilize the internal control loop. Many types of capacitors
are available, with different capacitance values tolerances, temperature
coefficients and equivalent series resistance. We recommend a
minimum of 4.7uF. To ensure good transient response from the power
supply system under rapidly changing current load conditions,
designers generally use additional output capacitors connected in
parallel. Such an arrangement serves to minimize the effects of the
parasitic resistance (ESR) and inductance (ESL) that are present in all
capacitors. The regulator has been tested stable with capacitor ESR’s
in the range of 0.05 to 2 ohms. We have found it best to use the same
type of capacitor for both input and output bypass.
Adjustable Output Voltage
The LX8816 develops a 1.25V reference voltage between the adjust
terminal and GND (See Figure 2). By placing a resistor, R2, between
these two terminals, a constant current is caused to flow through R1
and down through R2 to set the overall output voltage. Because I
very small and constant when compared with the current through R2, it
represents a small error and can usually be ignored.
Minimum Load Requirement
The LX8816 has a minimum load is requirement for proper output
regulation. This minimum current is specified at 0mA for the fixed
output and 2ma for the adjustable output regulators.
V
1
TM
FIGURE 2 - BASIC ADJUSTABLE
V
=
IN
V
REF
⎛
⎜ ⎜
⎝
1
LX8816-04
REGULATOR
+
R
R
11861 Western Avenue, Garden Grove, CA. 92841, 714-898-8121, Fax: 714-893-2570
1
2
1µA
I
ADJ
⎞
⎟
⎠
+
I
ADJ
ADJ
R
1
V
REF
V
V
2
1
A P P L I C A T I O N I N F O R M A T I O N
R1
R2
Integrated Products
®
Microsemi
1
, V
ADJ
2
and
is
Dual Channel 1A Low Dropout Regulator
Temperature Protection
The thermal protection shuts the LX8816 down when the junction
temperature exceeds 140
shutdown capability. Exposure to absolute maximum rated conditions
for extended periods may affect device reliability, see Thermal
Considerations below.
Current Limit Protection
The LX8816 includes over current protection, when the output load
current exceeds typically 1.4A the circuit forces the regulator decrease
in output.
Thermal Considerations
Thermal shutdown protects the integrated circuit from thermal
overload caused from a rise in junction temperature during power
dissipation. This means of protection is intended for fault protection
only and not as a means of current or power limiting during normal
application usage. Proper thermal evaluation should be done to ensure
that the junction temperature dose not exceed it’s maximum rating.
Operating at the maximum T
variation in individual device electrical characteristics and thermal
resistance , the built in thermal overload protection may be activated at
power levels slightly above or below the rated dissipation. Also peak
output power should be considered for each individual output.
Power dissipation for regulator can be calculated using the following
equation:
P
For the S-PAK package, thermal resistance, θ
depending on mounting technique when mounted on a FR4 copper clad
PCB. Junction temperature of the integrated circuit can be calculated
using:
T
T
T
T
T
T
(Note: power dissipation resulting from quiescent (ground) current is negligible)
An example: Given conditions: T
210mA, V
Calculated values:
It is important to note that although each output of the regulator will
produce up to 1A in current, the individual or total power dissipation
may limit the useful total current draw. The junction temperature
should be calculated for each individual output as well as the combined
outputs to insure the maximum junction temperature in not exceeded.
D
JUNCTION
TAB
J-TAB REG1
J-TAB REG2
TAB-AMB RISE
JUNCTION
= (5V-3.3V) * (1.0A) * 4.5°C/W = (1.7) * 4.5°C/W = 7.7°C
= (V
= (5V-2.5V) * (210mA) * 4.5°C/W = (0.525) * 4.5°C/W = 2.4°C
= P
IN(MAX)
D MAX
P
2
= 3.3V I
= T
=
RODUCTION
10.1°C + 66.8°C +
JUNCTION-TAB RISE _
= ( 0.525W + 1.7W ) * 30°C/W = 66.8°C
-V
* θ
1
2
) * I
JT ;
= 1A.
1
T
0
+
C. Each output has independent thermal
TAB-AMB
D
J
(V
ATA
of 150°C can impact reliability . Due to
IN(MAX)
5
A
0°C = 126.9°C
S
+ T
= 50°C, V
= (P
HEET
-V
TAB-AMB RISE
D REG1
2
) * I
IN
TAB-AMB
+ P
= 5.0V, V
2
D REG2
LX8816
+ T
is 25-45
AMB
1
) * θ
= 2.5V, I
Page 6
PCB
0
C/W
1
=