M25PE10 Numonyx, B.V., M25PE10 Datasheet - Page 30
![no-image](/images/no-image-200.jpg)
M25PE10
Manufacturer Part Number
M25PE10
Description
1 and 2 Mbit, page-erasable serial Flash memories with byte alterability, 75 MHz SPI bus, standard pinout
Manufacturer
Numonyx, B.V.
Datasheet
1.M25PE10.pdf
(64 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M25PE10-VMN6TP
Manufacturer:
MICRON
Quantity:
20 000
Company:
Part Number:
M25PE10-VMN6TP
Manufacturer:
Numonyx
Quantity:
20 000
Part Number:
M25PE10-VMN6TP
Manufacturer:
MICRON
Quantity:
20 000
Company:
Part Number:
M25PE10-VMN6TPBA
Manufacturer:
Lattice
Quantity:
242
Company:
Part Number:
M25PE10VMN6TP
Manufacturer:
CYPRESS
Quantity:
3 077
Part Number:
M25PE10VP
Manufacturer:
ST
Quantity:
20 000
Instructions
30/64
Table 10.
1. As defined by the values in the Block Protect (BP1, BP0) bits of the Status Register, as shown in
The protection features of the device are summarized in
When the Status Register Write Disable (SRWD) bit of the Status Register is 0 (its initial
delivery state), it is possible to write to the Status Register provided that the Write Enable
Latch (WEL) bit has previously been set by a Write Enable (WREN) instruction, regardless
of the whether Write Protect (W) is driven High or Low.
When the Status Register Write Disable (SRWD) bit of the Status Register is set to ‘1’, two
cases need to be considered, depending on the state of Write Protect (W):
●
●
Regardless of the order of the two events, the Hardware Protected Mode (HPM) can be
entered:
●
●
The only way to exit the Hardware Protected Mode (HPM) once entered is to pull Write
Protect (W) High.
If Write Protect (W) is permanently tied High, the Hardware Protected mode (HPM) can
never be activated, and only the Software Protected mode (SPM2), using the Block Protect
(BP1, BP0) bits of the Status Register, can be used.
signal
W
1
0
1
0
If Write Protect (W) is driven High, it is possible to write to the Status Register provided
that the Write Enable Latch (WEL) bit has previously been set by a Write Enable
(WREN) instruction
If Write Protect (W) is driven Low, it is not possible to write to the Status Register even
if the Write Enable Latch (WEL) bit has previously been set by a Write Enable (WREN)
instruction. Attempts to write to the Status Register are rejected, and are not accepted
for execution. As a consequence, all the data bytes in the memory area that are
software protected (SPM2) by the Block Protect (BP1, BP0) bits of the Status Register,
are also hardware protected against data modification.
by setting the Status Register Write Disable (SRWD) bit after driving Write Protect (W)
Low
or by driving Write Protect (W) Low after setting the Status Register Write Disable
(SRWD) bit.
SRWD
bit
0
0
1
1
Protection modes (T9HX process only, see
Protected
Hardware
Protected
Software
Second
(SPM2)
(HPM)
Mode
Status Register is writable
(if the WREN instruction
has set the WEL bit)
The values in the SRWD,
BP1 and BP0 bits can be
changed
Status Register is
Hardware write protected
The values in the SRWD,
BP1 and BP0 bits cannot
be changed
Write protection of the
Status Register
Protected area
Protected against
Sector Erase and
Protected against
Sector Erase and
Page Program,
Page Program,
Bulk Erase
Bulk Erase
Table
Important note on page
10.
Memory content
(1)
M25PE20, M25PE10
Unprotected area
Page Program and
Page Program and
Ready to accept
Ready to accept
Sector Erase
Sector Erase
instructions
instructions
Table
6)
3.
(1)