LT1616ES6 Linear Technology Corporation, LT1616ES6 Datasheet
LT1616ES6
Available stocks
Related parts for LT1616ES6
LT1616ES6 Summary of contents
Page 1
... Current limiting provides protection against shorted outputs. The low current (<1 A) shutdown provides complete output disconnect, enabling easy power management in battery-powered systems. , LTC and LT are registered trademarks of Linear Technology Corporation 0.01 F ...
Page 2
... SHDN SHDN Note 3: Current limit guaranteed by design and/or correlation to static test. Slope compensation reduces current limit at higher duty cycle ORDER PART NUMBER LT1616ES6 SHDN S6 PART MARKING LTNB = 250 MIN TYP MAX UNITS 3.35 3 ...
Page 3
W U TYPICAL PERFOR A CE CHARACTERISTICS Efficiency OUT 100 12V 24V 100 200 300 400 500 LOAD CURRENT ...
Page 4
LT1616 W U TYPICAL PERFOR A CE CHARACTERISTICS Oscillator Frequency 2.00 1.75 1.50 1.25 1.00 0.75 0.50 0.25 0 –25 0 –50 TEMPERATURE ( CTIO S BOOST (Pin 1): The BOOST pin is used ...
Page 5
W BLOCK DIAGRA INT REG SHDN 4 AND UVLO SLOPE COMP OSC FREQUENCY FOLDBACK U OPERATIO (Refer to Block Diagram) The LT1616 is a constant frequency, current mode Buck regulator. The 1.4MHz oscillator enables an RS flip-flop, ...
Page 6
LT1616 U U APPLICATIO S I FOR ATIO The LT1616 efficiently converts power from an input volt- age source to a lower output voltage using an inductor for energy storage. The LT1616 uses its internal power switch and an external ...
Page 7
U U APPLICATIO S I FOR ATIO Inductor Selection and Maximum Output Current The duty cycle of the internal switch is )/(V – OUT where V is the forward ...
Page 8
LT1616 U U APPLICATIO S I FOR ATIO Table 1. Inductor Vendors Vendor Phone Murata (404) 426-1300 Sumida (847) 956-0666 Coilcraft (847) 639-6400 Coiltronics (407) 241-7876 Toko Table 2. Capacitor Vendors Vendor Phone Taiyo-Yuden (408) 573-4150 AVX (803) 448-9411 Murata ...
Page 9
U U APPLICATIO S I FOR ATIO C = 4.7 F CERAMIC, CASE SIZE 0805 OUT CERAMIC, CASE SIZE 1206 OUT ESR 0.080 (SANYO POSCAP 6TPA47M) OUT C CASE C = 100 ...
Page 10
LT1616 U U APPLICATIO S I FOR ATIO BOOST Pin Considerations Capacitor C3 and diode D2 are used to generate a boost voltage that is higher than the input voltage. In most cases a 0.01 F capacitor and fast switching ...
Page 11
U U APPLICATIO S I FOR ATIO Shorted Input Protection If the inductor is chosen so that it won’t saturate exces- sively, an LT1616 buck regulator will tolerate a shorted output. There is another situation to consider in systems where ...
Page 12
LT1616 U U APPLICATIO S I FOR ATIO catch diode (D1) and the input capacitor (C1). The loop formed by these components should be as small as possible. Furthermore, the system ground should be tied to the regulator ground in ...
Page 13
U TYPICAL APPLICATIO S 16V TO 25V OFF ON 3.6V TO 12V OFF ON 12V Output BOOST IN C3 LT1616 0. SHDN SW GND 86. ...
Page 14
LT1616 U TYPICAL APPLICATIO S 3.6V TO 16V OFF 25V OFF ON 14 2.5V Output BOOST IN C3 LT1616 0. SHDN SW GND FB R1 10k 2 3 ...
Page 15
... MOLD FLASH SHALL NOT EXCEED 0.254mm 5. PACKAGE EIAJ REFERENCE IS SC-74A (EIAJ) Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no represen- tation that the interconnection of its circuits as described herein will not infringe on existing patent rights. U Dimensions in inches (millimeters) unless otherwise noted ...
Page 16
... Lower Current, 100% Duty Cycle High Efficiency, No Diode Required, 8-Lead MSOP L1A 22 H • 5V 200mA 6.3V GND L1B 6.3V –5V 100mA 1616 TA06 Noise RMS Noise, 8-Lead MSOP Package RMS sn1616 1616fs LT/TP 0201 4K • PRINTED IN USA LINEAR TECHNOLOGY CORPORATION 2000 ...