BTS 712N1 Infineon Technologies, BTS 712N1 Datasheet

Page 1

Smart High-Side Power Switch PROFET BTS712N1 ...

Page 2

Smart Four Channel Highside Power Switch Features Overload protection Current limitation Short-circuit protection Thermal shutdown Overvoltage protection (including load dump) Fast demagnetization of inductive loads 1 ) Reverse battery protection Undervoltage and overvoltage shutdown with auto-restart and hysteresis Open drain ...

Page 3

Block diagram Four Channels; Open Load detection in off state; 9 Data Sheet Smart High-Side Power Switch 3 BTS712N1 Rev 1.3, 2010-03-16 ...

Page 4

Maximum Ratings 25°C unless otherwise specified j Parameter Supply voltage (overvoltage protection see page 4) Supply voltage for full short circuit protection T = -40 ...+150°C j,start Load current (Short-circuit current, see page 5) ) Load dump ...

Page 5

Electrical Characteristics Parameter and Conditions ° unless otherwise specified j bb Load Switching Capabilities and Characteristics On-state resistance ( OUT 1.8 A each channel, L two parallel channels, ...

Page 6

Parameter and Conditions ° unless otherwise specified j bb Standby current, all channels off Operating current 5V ...

Page 7

Parameter and Conditions ° unless otherwise specified j bb Input and Status Feedback Input resistance (see circuit page 8) Input turn-on threshold voltage Input turn-off threshold voltage Input threshold hysteresis Off state ...

Page 8

... Z = high impedance, potential depends on external circuit ,R = 150 GND1/2 GND3/4 in the off state causes an internal current from output to ground Smart High-Side Power Switch OUT2 ST1/2 ST1/2 OUT4 ST3/4 ST3/4 BTS 711L1 BTS 712N1 ...

Page 9

Input circuit (ESD protection), ESD zener diodes are not to be used as voltage clamp at DC conditions. Operation in this mode may result in a drift of the zener voltage (increase V). Status output, ST1/2 ...

Page 10

GND disconnect (channel 1/2 or 3/4) Any kind of load. In case high is V Due to V > low signal available. GND ST GND disconnect with GND pull up (channel 1/2 or ...

Page 11

Typ. on-state resistance ; high L R [mOhm] ON Typ. standby current ; V = 9... 1...4 = low bb I [µA] bb(off) I bb(off) includes four times the current I L(off) ...

Page 12

Timing diagrams Timing diagrams are shown for chip 1 (channel 1/2). For chip 2 (channel 3/4) the diagrams are valid too. The channels 1 and 2, respectively 3 and 4, are symmetric and consequently the diagrams are valid for each ...

Page 13

Figure 3b: Turn on into short circuit: shut down by overtemperature, restart by cooling (two parallel switched channels 1 and 2) Figure 4a: Overtemperature: Reset if T < Data Sheet Smart High-Side Power Switch Figure 5a: Open ...

Page 14

Figure 6b: Undervoltage restart of charge pump IN = high, normal load conditions. Charge pump starts 5.6 V typ. bb(ucp) Figure 7a: Overvoltage bb(over) ON(CL) bb Data Sheet Smart High-Side Power Switch V bb(o rst) ...

Page 15

Package Outlines 1.27 +0.15 0.35 Index Marking 1) Does not include plastic or metal protrusions of 0.15 max per side 2) Does not include dambar protrusion of 0.05 max per side Figure 1 PG-DSO-20 (Plastic Dual Small Outline Package) (RoHS-compliant) ...

Page 16

Revision History Version Date Changes Rev 1.3 2010-03-16 page 6: changed reference to the timing diagram Rev 1.2 2009-07-13 page 1: added new coverpage page 6: Initial short circuit shutdown time changed: t off(SC) -40 ° ...

Page 17

... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...