BTS 723GW Infineon Technologies, BTS 723GW Datasheet
BTS 723GW
Specifications of BTS 723GW
Related parts for BTS 723GW
BTS 723GW Summary of contents
Page 1
Product Summary • • • • • • • • • • • • • • • • • • • • • • • • • • Data Sheet Smart High-Side Power Switch Ω Ω Ω Block Diagram ...
Page 2
Data Sheet Smart High-Side Power Switch 2 BTS723GW V1.1, 2007-09-25 ...
Page 3
Pin Definitions and Functions Pin Symbol Function Positive power supply voltage. Design the 1,7, wiring for the simultaneous max. short circuit V bb 8,14, currents from channel and also for low thermal resistance 2 IN1 Input 1,2 ...
Page 4
Parameter Supply voltage (overvoltage protection see page 6) Supply voltage for full short circuit protection T = -40 ...+150°C j,start Output Voltage Negative voltage slope at output Load current (Short-circuit current, see page ...
Page 5
Parameter and Conditions Thermal resistance junction - soldering point 5),6) junction - ambient 5) Electrical Characteristics Parameter and Conditions -40...+150° unless otherwise specified j bb Load Switching Capabilities and Characteristics On-state resistance (V ...
Page 6
Parameter and Conditions -40...+150° unless otherwise specified j bb Nominal load current two parallel channels active 85° ≤ 150°C 7 Device on PCB Output current while ...
Page 7
Parameter and Conditions -40...+150° unless otherwise specified j bb 14) Protection Functions Current limit, (see timing diagrams, page 13) Repetitive short circuit current limit (see timing diagrams, page ...
Page 8
Parameter and Conditions -40...+150° unless otherwise specified j bb Diagnostic Characteristics Open load detection current Open load detection voltage Short circuit detection voltage V (pin 1,7,8,14) to OUT1 (pin 12,13) resp ...
Page 9
Truth Table Channel 1 Input 1 Output 1 Channel 2 Input 2 Output 2 level Normal L operation H V Open load L OUT H Short circuit L to GND H Short circuit Overtem- L ...
Page 10
Input circuit (ESD protection), The use of ESD zener diodes as voltage clamp at DC conditions is not recommended. Status output, ST1 or ST2 ESD-Zener diode: 6.1 V typ., R ST(ON) = 850 Ω typ kΩ ...
Page 11
Open-load detection, OUT1 or OUT2 OFF-state diagnostic condition: Open load > 2.7 V typ. (IN low) OUT I typ. 2µA L(OL) An external resitor can be used to increase the open load detection current GND disconnect Any kind ...
Page 12
Inductive load switch-off energy dissipation Energy stored in load inductance · · While demagnetizing load inductance, the energy dissipated in PROFET ...
Page 13
Timing diagrams All channels are symmetric and consequently the diagrams are valid for channel 1 and channel 2 Figure 1a: V turn on case of too early V IN =high the device may not turn on (curve ...
Page 14
Figure 4a: Overtemperature: Reset if T < Figure 5a: Open load, : detection in OFF-state, open load occurs in off-state = 2 µA typ > 2.7V L OUT Data Sheet Smart High-Side Power Switch ...
Page 15
Package Outlines Figure 1 PG-DSO-14-37 (Plastic Dual Small Outline Package) (RoHS-compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant ...
Page 16
Revision History Version Date Changes V1.1 2007-09-25 Modification of the package drawing V1.0 2007-05-25 Creation of the green datasheet. First page : Adding the green logo and the AEC qualified Adding the bullet AEC qualified and the RoHS compliant features ...
Page 17
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...