BTS 716G Infineon Technologies, BTS 716G Datasheet
BTS 716G
Specifications of BTS 716G
Related parts for BTS 716G
BTS 716G Summary of contents
Page 1
Product Summary • • • • • • • • • • • • • • • • • • • • • • • • Data Sheet Smart High-Side Power Switch Ω Ω Ω Block Diagram 1 BTS716G ...
Page 2
IN4 Data Sheet control and protection circuit of channel 2 control and protection circuit of channel 3 control and protection circuit of channel 4 2 Smart High-Side Power Switch BTS716G V1.0, 2007-05-13 ...
Page 3
Pin Definitions and Functions Pin Symbol Function 1,10, V Positive power supply voltage. Design the bb 11,12, wiring for the simultaneous max. short circuit 15,16, currents from channel and also for low 19,20 thermal resistance 3 IN1 ...
Page 4
Parameter Supply voltage (overvoltage protection see page 6) Supply voltage for full short circuit protection T = -40 ...+150°C j,start Load current (Short-circuit current, see page 6) ) Load dump protection 1 V LoadDump = 2 Ω ...
Page 5
Parameter and Conditions Thermal resistance junction - soldering point 6)7) junction – ambient cooling area Electrical Characteristics Parameter and Conditions -40...+150° unless otherwise specified j bb Load Switching ...
Page 6
Parameter and Conditions, = -40...+150° unless otherwise specified j bb Operating Parameters Operating voltage ) Undervoltage switch off 10 ) Overvoltage protection Standby current ...
Page 7
Parameter and Conditions -40...+150° unless otherwise specified j bb Reverse Battery ) 17 Reverse battery voltage Drain-source diode voltage = - 2 +150° Diagnostic Characteristics Open load ...
Page 8
Truth Table Channel 1 and 2 Channel 3 and 4 (equivalent to channel 1 and 2) Normal operation Open load Overtemperature L = "Low" Level X = don't care H = "High" Level Status signal valid after the time delay ...
Page 9
Input circuit (ESD protection), The use of ESD zener diodes as voltage clamp at DC conditions is not recommended. Status output, ST1/2 or ST3/4 ESD-Zener diode: 6.1 V typ., max 0.3 mA 1.6 mA. The use of ESD ...
Page 10
GND disconnect with GND pull up Any kind of load > GND IN IN(T+) Due to V > low signal available. GND ST V disconnect with energized inductive bb load For ...
Page 11
Typ. on-state resistance high L R [mOhm] ON Typ. standby current , I 9...34 V, IN1,2,3,4 = low EE RII ...
Page 12
Timing diagrams All channels are symmetric and consequently the diagrams are valid for channel 1 to channel 4 Figure 1a: V turn on: bb Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data Sheet Figure ...
Page 13
Figure 3b: Turn on into short circuit: shut down by overtemperature, restart by cooling (two parallel switched channels 1 and 2) ST1 and ST2 have to be configured as a 'Wired OR' function ST1/2 with a single pull-up resistor. Figure ...
Page 14
Package Outlines 1.27 +0.15 0.35 Index Marking 1) Does not include plastic or metal protrusions of 0.15 max per side 2) Does not include dambar protrusion of 0.05 max per side Figure 1 PG-DSO-20 (Plastic Dual Small Outline Package) (RoHS-compliant) ...
Page 15
Revision History Version Date Changes 1.0 2007-05-13 Creation of the green datasheet. Data Sheet Smart High-Side Power Switch 18 BTS716G V1.0, 2007-05-13 ...
Page 16
... Infineon Technologies Office. Infineon Technologies Components may only be used in life-support devices or systems with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life ...