BTS 5210G Infineon Technologies, BTS 5210G Datasheet
BTS 5210G
Specifications of BTS 5210G
Related parts for BTS 5210G
BTS 5210G Summary of contents
Page 1
...
Page 2
Product Summary • • • • • • • • • • • • • • • • • • • • • • • • • AEC Qualified • Green product (RoHS compliant) Data Sheet Smart High-Side Power Switch ...
Page 3
Data Sheet control and protection circuit equivalent to channel 1 3 Smart High-Side Power Switch BTS5210G Rev. 1.3, 2009-04-16 ...
Page 4
Pin Definitions and Functions Pin Symbol Function Positive power supply voltage. Design the 1,7, wiring for the simultaneous max. short circuit V bb 8,14 currents from channel and also for low thermal resistance 2 GND Logic Ground ...
Page 5
Parameter Supply voltage (overvoltage protection see page 6) Supply voltage for full short circuit protection T = -40 ...+150°C j,start Load current (Short-circuit current, see page 6) ) Load dump protection 1 V LoadDump = 2 Ω ...
Page 6
Parameter and Conditions Thermal resistance junction - soldering point 6)7) junction – ambient cooling area Electrical Characteristics Parameter and Conditions -40...+150° unless otherwise specified j bb Load Switching ...
Page 7
Parameter and Conditions, = -40...+150° unless otherwise specified j bb Operating Parameters Operating voltage ) Undervoltage switch off 10 ) Overvoltage protection Standby current ...
Page 8
Parameter and Conditions -40...+150° unless otherwise specified j bb Reverse Battery ) 17 Reverse battery voltage Drain-source diode voltage = - 2 +150° Diagnostic Characteristics Open load ...
Page 9
Truth Table ( each channel ) Normal operation Open load Overtemperature L = "Low" Level X = don't care H = "High" Level Status signal valid after the time delay shown in the timing diagrams Parallel switching of channel 1 ...
Page 10
Input circuit (ESD protection), The use of ESD zener diodes as voltage clamp at DC conditions is not recommended. Status output, ST1 or ST2 ESD-Zener diode: 6.1 V typ., max 0.3 mA 1.6 mA. The use of ESD ...
Page 11
GND disconnect with GND pull up Any kind of load > GND IN IN(T+) Due to V > low signal available. GND ST V disconnect with energized inductive bb load For ...
Page 12
Typ. on-state resistance high L R [mOhm] ON Typ. standby current , I 9...34 V, IN1,2 = low EE RII ...
Page 13
Timing diagrams All channels are symmetric and consequently the diagrams are valid for channel 1 to channel 4 Figure 1a: V turn on: bb Figure 2a: Switching a resistive load, turn-on/off time and slew rate definition: on Data Sheet Figure ...
Page 14
Figure 3b: Turn on into short circuit: shut down by overtemperature, restart by cooling (two parallel switched channels 1 and 2) ST1 and ST2 have to be configured as a 'Wired OR' function ST1/2 with a single pull-up resistor. Figure ...
Page 15
Package Outlines Figure 1 PG-DSO-14-37 (Plastic Dual Small Outline Package) (RoHS-compliant) To meet the world-wide customer requirements for environmentally friendly products and to be compliant with government regulations the device is available as a green product. Green products are RoHS-Compliant ...
Page 16
Revision History Version Date Changes Rev. 1.3 2009-04-16 Modification of the package name extension. V1.2 2007-09-25 Modification of the package drawing. V1.1 2007-05-29 Creation of the green datasheet. First page : Adding the green logo and the AEC qualified Adding ...
Page 17
... Infineon Technologies Office. Infineon Technologies components may be used in life-support devices or systems only with the express written approval of Infineon Technologies failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. Life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life ...