TLE 4254EJ A Infineon Technologies, TLE 4254EJ A Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/3/327/infineon_technologies_sml.jpg)
TLE 4254EJ A
Manufacturer Part Number
TLE 4254EJ A
Description
Manufacturer
Infineon Technologies
Datasheet
1.TLE_4254EJ_A.pdf
(21 pages)
Specifications of TLE 4254EJ A
Packages
PG-DSO-8
Regulator Type
tracker
Output Voltage
adj.
Accuracy
0.1 %
Max. Output Current
70mA
Dropout Voltage
200mV
5
5.1
The output voltage
transistor accordingly. The control loop stability depends on the output capacitor
temperature and the poles/zeros introduced by the integrated circuit and the load. To ensure stable operation, the
output capacitor’s capacitance and its equivalent series resistor ESR requirements given in the table “Functional
Range” have to be maintained. For details see also the typical performance graph “Output Capacitor Series
Resistor
An input capacitor
terminals.
Protection circuitry prevent the IC as well as the application from destruction in case of catastrophic events. These
safeguards contain output current limitation, reverse polarity protection as well as thermal shutdown in case of
overtemperature.
In order to avoid excessive power dissipation that could never be handled by the pass element and the package,
the maximum output current is decreased at high input voltages.
The overtemperature protection circuit prevents the IC from immediate destruction under fault conditions (e. g.
output continuously short-circuited) by reducing the output current. A thermal balance below 200 °C junction
temperature is established. Please note that a junction temperature above 150 °C is outside the maximum ratings
and reduces the IC lifetime.
The TLE4254 allows a negative supply voltage. However, several small currents are flowing into the IC increasing
its junction temperature. This has to be considered for the thermal design, respecting that the thermal protection
circuit is not operating during reverse polarity condition.
Table 1
V
all voltages with respect to ground (unless otherwise specified).
Pos.
5.1.1
5.1.2
5.1.3
5.1.4
5.1.5
Data Sheet
I
= 13.5 V;
Parameter
Output Voltage Tracking
Accuracy
∆
Load Regulation
steady-state
steady-state
Line Regulation
ESR
V
Q
V
Electrical Characteristics
Tracking Regulator
Electrical Characteristics Tracking Regulator
=
CQ
ADJ/EN
V
vs. Output Current
EN/ADJ
C
V
≥ 2.0 V;
I
Q
is strongly recommended to buffer line influences. Connect the capacitors close to the IC
is controlled by comparing it to the voltage applied at pin ADJ/EN and driving a PNP pass
-
V
Q
V
FB
=
V
I
Q
Q
”. Also, the output capacitor shall be sized to buffer load transients.
(version GA / EJ A); -40 °C ≤
Symbol
∆
|d
|d
V
V
V
Q
Q,load
Q,line
|
| –
Min.
-5
-10
-10
–
Limit Values
8
–
–
–
Typ.
1
1
Max.
5
10
10
10
10
T
j
≤ 150 °C;
Unit
mV
mV
mV
mV
mV
Test Condition
8 V ≤
0.1 mA ≤
V
5.5 V ≤
0.1 mA ≤
V
5.5 V ≤
0.1 mA ≤
V
I
V
V
I
V
C
Q
Q
ADJ/EN
ADJ/EN
ADJ/EN
ADJ/EN
I
ADJ/EN
Q
= 5.5 V to 32 V;
= 0.1 mA to 70 mA;
= 5 mA
C
= 1 µF;
Q
Electrical Characteristics
, the load current, the chip
V
I
= 5 V
= 5 V
= 5 V
= 5 V
= 5 V
V
V
≤ 18 V;
I
I
I
I
I
≤ 26 V;
≤ 32 V;
Q
Q
Q
Rev. 1.2, 2009-11-18
≤ 60 mA;
≤ 60 mA;
≤ 30 mA;
TLE4254