IR3551MTRPBF International Rectifier, IR3551MTRPBF Datasheet
IR3551MTRPBF
Specifications of IR3551MTRPBF
Available stocks
Related parts for IR3551MTRPBF
IR3551MTRPBF Summary of contents
Page 1
FEATURES Peak efficiency up to 94.5% at 1.2V Integrated driver, control MOSFET, synchronous MOSFET and Schottky diode Input voltage (VIN) operating range up to 15V Output voltage range from 0.25V up to 3.3V Output current ...
Page 2
... VCC VIN BOOST Gate SW Drivers and Current Sense Amplifier PGND PGND 4 CSIN- CSIN IR3551 Tape & Reel Qty Part Number 3000 IR3551MTRPBF Qty Part Number 100 IR3551MPBF VIN 4.5V to 15V C1 C2 0.1uF 10uF 0.22uF 150nH C6 C7 22uF 470uF 6- ...
Page 3
TYPICAL APPLICATION DIAGRAM (CONTINUED) VCC C3 4. 0.1uF R1 IR3551 10k 21 PHSFLT# PHSFLT# 22 PWM PWM 23 BBRK# BBRK# 24 LGND 25 REFIN 26 IOUT TGND 27 No Connect Figure 5: Application Circuit without Current Sense Amplifier ...
Page 4
PIN DESCRIPTIONS PIN # PIN NAME 1 CSIN- 2 CSIN+ 3 VCC 4, 14, 15 PGND 5, 28 GATEL 6 – – 19 VIN 20 BOOST 21 PHSFLT# 22 PWM 23 BBRK# 24 LGND 25 REFIN 26 ...
Page 5
... MSL Rating Reflow Temperature Note: 1. Thermal Resistance (θ measured with the component mounted on a high effective thermal conductivity test board in free air. JA Refer to International Rectifier Application Note AN-994 for details. March 12, 2012 | FINAL DATASHEET 5 50A Integrated PowIRstage® MAX MIN VCC + 0 ...
Page 6
ELECTRICAL SPECIFICATIONS The electrical characteristics involve the spread of values guaranteed within the recommended operating conditions. Typical values represent the median values, which are related to 25°C. RECOMMENDED OPERATING CONDITIONS FOR RELIABLE OPERATION WITH MARGIN PARAMETER Recommended VIN Range Recommended ...
Page 7
PARAMETER Slew Rate Differential Input Range Common Mode Input Range Output Impedance (IOUT) IOUT Sink Current Diode Emulation Mode Comparator Input Offset Voltage Leading Edge Blanking Time Negative Current Time-Out Digital Input – BBRK# Input voltage high Input voltage low ...
Page 8
PARAMETER VCC Supply Current VIN Supply Leakage Current BOOST Supply Current REFIN Bias Current SW Floating Voltage SW Pull Down Resistance Notes 1. Guaranteed by design but not tested in production 2. V =12V, V =1.2V, ƒ = 300kHz, L=210nH ...
Page 9
TYPICAL OPERATING CHARACTERISTICS Circuit of Figure 32, V =12V, V =1.2V, ƒ IN OUT 8-layer PCB board of 3.7” (L) x 2.6” (W), no PWM controller loss, no inductor loss, unless specified otherwise ...
Page 10
TYPICAL OPERATING CHARACTERISTICS (CONTINUED) Circuit of Figure 32, V =12V, V =1.2V, ƒ IN OUT 8-layer PCB board of 3.7” (L) x 2.6” (W), no PWM controller loss, no inductor loss, unless specified otherwise. 1.20 1.15 1.10 1.05 1.00 0.95 ...
Page 11
TYPICAL OPERATING CHARACTERISTICS (CONTINUED) Circuit of Figure 32, V =12V, V =1.2V, ƒ IN OUT 8-layer PCB board of 3.7” (L) x 2.6” (W), no PWM controller loss, no inductor loss, unless specified otherwise. 40ns/div Figure 19: Body-Braking® Delays 100ns/div ...
Page 12
TYPICAL OPERATING CHARACTERISTICS (CONTINUED) Circuit of Figure 32, V =12V, V =1.2V, ƒ IN OUT 8-layer PCB board of 3.7” (L) x 2.6” (W), no PWM controller loss, no inductor loss, unless specified otherwise. 4ms/div Figure 25: Diode Emulation Setup ...
Page 13
... BODY-BRAKING® MODE International Rectifier’s Body-Braking® operation mode in which two MOSFETs are turned off. When the synchronous MOSFET is off, the higher voltage across the Shottky diode in parallel helps discharging the inductor current faster, which reduces the output voltage overshoot. The Body-Braking® ...
Page 14
MOSFET, allowing the switch node to float. This is in contrast to the Body-Braking® mode shown in Figure 23, where GATEL follows PWM input. The Schottky diode in parallel with the synchronous MOSFET ...
Page 15
L over the inductor DCR ( the two time constants match, the voltage across proportional to the current through L, and the sense circuit can be treated as if only ...
Page 16
If any of the application condition, i.e. input voltage, output voltage, switching frequency, VCC MOSFET driver voltage or inductance, is different from those of Figure 8, a set of normalized power loss curves should be used. Obtain the normalizing factors ...
Page 17
... In very high duty cycle applications sufficient time must be provided for replenishment of the Bootstrap capacitor for the control MOSFET drive. LAYOUT EXAMPLE Contact International Rectifier for a layout example suitable for your specific application. VCC IR3551 ...
Page 18
... Contact International Rectifier to receive an electronic PCB Library file in Cadence Allegro or CAD DXF/DWG format. March 12, 2012 | FINAL DATASHEET 18 50A Integrated PowIRstage® Center pad land length and width should be equal to maximum part pad length and width. ...
Page 19
... At the inside corner of the solder resist where the lead land groups meet recommended to provide a fillet so a solder resist width of ≥ 0.17mm remains. * Contact International Rectifier to receive an electronic PCB Library file in Cadence Allegro or CAD DXF/DWG format. March 12, 2012 | FINAL DATASHEET 19 50A Integrated PowIRstage® ...
Page 20
... The low power signal stencil lead land apertures should therefore be shortened in length to keep area ratio of 65% to 75% while centered on lead land. * Contact International Rectifier to receive an electronic PCB Library file in Cadence Allegro or CAD DXF/DWG format. March 12, 2012 | FINAL DATASHEET 20 50A Integrated PowIRstage® ...
Page 21
MARKING INFORMATION Site/Date/Marking Code PACKAGE INFORMATION March 12, 2012 | FINAL DATASHEET 21 50A Integrated PowIRstage® 3551M ?YWW? xxxxx Lot Code Figure 36: PQFN 5mm x 6mm Figure 37: PQFN 5mm x 6mm IR3551 ...
Page 22
IR WORLD HEADQUARTERS: March 12, 2012 | FINAL DATASHEET 22 50A Integrated PowIRstage® Data and specifications subject to change without notice. This product will be designed and qualified for the Industrial market. Qualification Standards can be found on IR’s Web ...