IR3898MTRPBF International Rectifier, IR3898MTRPBF Datasheet - Page 20
![no-image](/images/manufacturer_photos/0/3/338/international_rectifier_sml.jpg)
IR3898MTRPBF
Manufacturer Part Number
IR3898MTRPBF
Description
6A Highly Integrated Single-Input Voltage, Synchronous Buck Regulator in a PQFN package.
Manufacturer
International Rectifier
Datasheet
1.IR3898MTR1PBF.pdf
(42 pages)
Specifications of IR3898MTRPBF
Part Status
Active and Preferred
Package
PQFN / 4 x 5
Circuit
Single Output
Iout (a)
6
Switch Freq (khz)
0 - 1500
Input Range (v)
1.0 - 16
Output Range (v)
0.5 - 12
Pbf
PbF Option Available
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IR3898MTRPBF
Manufacturer:
IOR
Quantity:
30
Part Number:
IR3898MTRPBF
Manufacturer:
IR
Quantity:
20 000
I
I
Δi=Inductor ripple current
THERMAL SHUTDOWN
Temperature sensing is provided inside IR3898. The trip
threshold is typically set to 145
exceeded, thermal shutdown turns off both MOSFETs and
resets the internal soft start.
Automatic restart is initiated when the sensed
temperature drops within the operating range. There is
a 20
EXTERNAL SYNCHRONIZATION
IR3898 incorporates an internal phase lock loop (PLL)
circuit which enables synchronization of the internal
oscillator to an external clock. This function is important to
avoid sub‐harmonic oscillations due to beat frequency for
embedded systems when multiple point‐of‐load (POL)
regulators are used. A multi‐function pin, Rt/Sync, is used
to connect the external clock. If the external clock is
present before the converter turns on, Rt/Sync pin can be
connected to the external clock signal solely and no other
resistor is needed. If the external clock is applied after the
converter turns on, or the converter switching frequency
needs to toggle between the external clock frequency and
the internal free‐running frequency, an external resistor
from Rt/Sync pin to Gnd is required to set the free‐running
frequency.
I
OCP
LIMIT
OCP
= DC current limit hiccup point
= Current limit Valley Point
o
C hysteresis in the thermal shutdown threshold.
ILIMIT
20
Figure 8: Timing Diagram for
Current Limit and Hiccup
FEBRUARY 02, 2012 | DATA SHEET | Rev 3.2
2
i
(2)
o
C. When trip threshold is
Single‐Input Voltage, Synchronous Buck Regulator
- 20 -
6A Highly Integrated SupIRBuck
When an external clock is applied to Rt/Sync pin after the
converter runs in steady state with its free‐running
frequency, a transition from the free‐running frequency to
the external clock frequency will happen. This transition is
to gradually make the actual switching frequency equal to
the external clock frequency, no matter which one is
higher. On the contrary, when the external clock signal is
removed from Rt/Sync pin, the switching frequency is also
changed to free‐running gradually. In order to minimize
the impact from these transitions to output voltage, a
diode is recommended to add between the external clock
and Rt/Sync pin. Figure 9 shows the timing diagram of
these transitions.
An internal circuit is used to change the PWM ramp slope
according to the clock frequency applied on Rt/Sync pin.
Even though the frequency of the external synchronization
clock can vary in a wide range, the PLL circuit will make
sure that the ramp amplitude is kept constant, requiring no
adjustment of the loop compensation. Vin variation also
affects the ramp amplitude, which will be discussed
separately in Feed‐Forward section.
.
SW
SYNC
Free Running
Fs1
Frequency
Figure 9: Timing Diagram for Synchronization
to the external clock (Fs1>Fs2 or Fs1<Fs2)
Gradually change
Fs2
Synchronize to the
external clock
...
...
TM
Gradually change
IR3898
Return to free-
PD‐97662
running freq
Fs1