TSM240160F TEAM SOURCE DISPLAY, TSM240160F Datasheet
TSM240160F
Specifications of TSM240160F
Related parts for TSM240160F
TSM240160F Summary of contents
Page 1
... Product Specification For Customer： Module No.： TSM240160F-49B For Customer’s Acceptance ： Approved by Team Source Display Presented by ---------------------------------------------------------------------------------------------------------------------------- LCD Module □：APPROVAL FOR SPECIFICATION □：APPROVAL FOR SAMPLE Comment ： Reviewed by Organized by ...
Page 2
... Team Source Display Table of Content 1. Basic Specifications……………….………………………………………………3 1.1 Display Specifications………………………..…………………………………………………………….….3 1.2 Mechanical Specifications… ...
Page 3
... Team Source Display 1. Basic Specifications 1.1 Display Specifications 1>LCD Display Mode 2>Viewing Angle 3>Driving Method 4 >Backlight 1.2 Mechanical Specifications 1>Outline Dimension : 87.0 x73.0 x 10.0mm (See attached Outline Drawing for Data) 1.3 Circuit Diagram /CS,A0,/WR,/RD,/RST VDD VSS DB0~DB7 BLA BLK www.tslcd.com : FSTN-32Gray, Negative, Transmissive ...
Page 4
... Team Source Display 1.4 Terminal Function 1.41 CON1 Pin No. Pin Name 1 VSS 2 VDD 3 NC（EN） 4 A0（RS） 5 //WR 6 /RD 7~14 DB0~DB7 15 /CS 16 /RST 17 BLA（+） 18 BLK（-） 1.42 CON2 Pin No. Pin Name 1 VSS 2 VDD 3~10 DB0~DB7 11 /WR 12 A0(RS) 13 /RD 14 /RST 15 /CS ...
Page 5
... Team Source Display 2. Absolute Maximum Ratings Items Supply Voltage Input Voltage Operating Temperature Storage Temperature 3. Electrical Characteristics 3.1 DC Characteristics Items Operating Voltage Input High Voltage Input Low Voltage Output High Voltage Output Low Voltage Input Leakage Current Output Leakage Current 3.2 LED Backlight Circuit (if need BLK) ...
Page 6
... Team Source Display 3.3 AC Characteristics 8080 Mode System Bus Timing Items System cycle time Address setup time(A0) Address hold time(A0) Control Low Pulse wide(/RD) Control Low Pulse wide(/WR) Control High Pulse wide(/RD) Control High Pulse wide(/WR) Data steup time Data hold time /RD access time(*a) ﹪ ...
Page 7
... Team Source Display 3.4 Reset Timing Items Reset time Reset Low pules width ﹪ Items Reset time Reset Low pules width Note: *a. all timing is using 20 www.tslcd.com Symbol MIN. TYP Trw 1 - ﹪ Symbol MIN. TYP Trw 1.5 - and 80 of VDD as the reference. LCM Specification (VDD=3.3V,Ta=-40-85℃ ...
Page 8
... Team Source Display 4. Function specifications 4.1 The Parallel Interface Shared /RST / 4.2 Basic Setting To drive the LCD module correctly and provide normally display, please use the following seting 1> COM Reverse Select = 0x00 (Normal. Or 0x01 Up and Down Reverse) 2> SEG Reverse Select = 0x00 (Normal. Or 0x02, Left and Right Reverse) 3> ...
Page 9
... Team Source Display 4.4 Display Commands www.tslcd.com LCM Specification Email: tslcd@tslcd.com ...
Page 10
... Team Source Display Note: *a. For the details of the Display Commands, please refer to ST7529 data sheet www.tslcd.com LCM Specification Email: tslcd@tslcd.com ...
Page 11
... Team Source Display 4.5 Basic Operating Sequence 4.5.1 Initialization Sequence Turn on Power Supply VDD & VSS While maintaining /RES at LOW Wait until power supply is stabilized Release the /RES Reset Signal (/RES = High) EXT=Use the “ext=0” Command Sleep Out Osc on Com scan dtrec ...
Page 12
... Team Source Display 4.5.2 8080serial 8-bit Inteface 上的接口顺序 www.tslcd.com 5倍压连接图，有参考程序 （指令/数据选择） （写信号） 数据总线端口 ...
Page 13
... Team Source Display 5. Inspection Standards Item (1) Non display 1) Display on inspection (3) Horizontal line is deficient (4) Cross line is deficient 2) Black／White spot Length (mm) 5.0≤L≤10 0.03<W≤0.04 5.0≤L≤10 0.04<W≤0.05 3) Black／White line 1.0≤L≤10 0.05<W≤0.06 1.0≤L≤10 0.06<W≤0.08 Defects separate with each other at an interval of more than 20mm 4) Display pattern A+B≤ ...
Page 14
... Team Source Display 6. Handling Precautions 6.1 Mounting method A panel of LCD module made by our company consists of two thin glass plates with polarizers that easily get damaged. And since the module in so constructed fixed by utilizing fitting holes in the printed circuit board (PCB), extreme care should be used when handling the LCD modules ...