MAX4567 Maxim, MAX4567 Datasheet - Page 8
MAX4567
Manufacturer Part Number
MAX4567
Description
The MAX4565/MAX4566/MAX4567 are low-voltage T-switches designed for switching RF and video signals from DC to 350MHz in 50Ω and 75Ω systems
Manufacturer
Maxim
Datasheet
1.MAX4565.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAX4567CEE
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX4567CSE
Manufacturer:
MAIXM
Quantity:
20 000
Company:
Part Number:
MAX4567CSE+
Manufacturer:
MAX
Quantity:
96
Part Number:
MAX4567CSE+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Part Number:
MAX4567EEE
Manufacturer:
MAIXM
Quantity:
20 000
Company:
Part Number:
MAX4567EEE+
Manufacturer:
Maxim Integrated Products
Quantity:
135
Company:
Part Number:
MAX4567EEE+
Manufacturer:
Maxim
Quantity:
3 545
Company:
Part Number:
MAX4567ESE
Manufacturer:
MAXIM
Quantity:
144
Quad/Dual, Low-Voltage,
Bidirectional RF/Video Switches
*
** NO_ (or NC_) and COM_ pins are identical and interchangeable. Either may be considered as an input or output; signals pass
The MAX4565/MAX4566/MAX4567 are high-frequency
“T” switches. Each “T” switch consists of two series
CMOS switches, with a third N-channel switch at the
junction that shunts capacitively-coupled signals to
ground when the series switches are off. This produces
superior high-frequency signal isolation when the
switch is turned off.
The MAX4565/MAX4566/MAX4567 are constructed as
high-frequency “T” switches, as shown in Figure 1. The
logic-level input, IN_, is translated by amplifier A1 into a
V+ to V- logic signal that drives amplifier A2. (Amplifier
A2 is an inverter for normally closed switches.)
Amplifier A2 drives the gates of N-channel MOSFETs
N1 and N2 from V+ to V-, turning them fully on or off.
The same signal drives inverter A3 (which drives the
P-channel MOSFETs P1 and P2) from V+ to V-, turning
them fully on or off, and drives the N-channel MOSFET
N3 off and on.
The logic-level threshold is determined by V+ and
GND_. The voltage on GND_ is usually at ground
potential, but it may be set to any voltage between
(V+ - 2V) and V-. When the voltage between V+ and
GND_ is less than 2V, the level translators become very
slow and unreliable. Since individual switches in each
package have individual GND_ pins, they may be set to
different voltages. Normally, however, they should all
be connected to the ground plane.
8
______________________________________________________________Pin Description
4, 7, 14, 17
2, 9, 12, 19
_______________Theory of Operation
3, 6, 8, 13,
MAX4565
1, 10, 11,
All pins have ESD diodes to V- and V+.
equally well in either direction.
15, 18
_______________________________________________________________________________________
20
16
—
5
3, 7, 10, 14
MAX4566
2, 8, 9, 15
1, 16
4, 13
6, 11
PIN
12
5
Logic-Level Translators
4, 6, 12, 14
MAX4567
7, 15
3, 11
2, 16
8, 10
5, 13
1, 9
NAME
COM_
GND_
NO_
NC_
IN_
V+
V-
Digital Control Input
RF and Logic Ground. Grounds are not internally connected to each other,
and should all be connected to a ground plane (see Grounding section).
Positive Supply-Voltage Input (analog and digital)
Negative Supply-Voltage Input. Connect to ground plane for single-supply
operation.
Analog Switch Normally Open** Terminals
Analog Switch Normally Closed** Terminals
Analog Switch Common** Terminals
Figure 1. T-Switch Construction
When the switch is on, MOSFETs N1, N2, P1, and P2
are on and MOSFET N3 is off. The signal path is COM_
to NO_, and because both N-channel and P-channel
MOSFETs act as pure resistances, it is symmetrical
(i.e., signals may pass in either direction). The off
MOSFET, N3, has no DC conduction, but has a small
COM_
GND_
IN_
0
1
IN_
V+
V-
COM_ - NO_
OFF
ON
A1
NORMALLY OPEN SWITCH CONSTRUCTION
FUNCTION*
D
A2
N1
S
S
A3
A2
Switch On Condition
P1
(NC)
D
COM_, NO_, AND NC_
D
S
N3
ON GND_, IN_,
D
ESD DIODES
S
N2
P2
S
D
V+
V-
NO_