DG528 Maxim, DG528 Datasheet
DG528
Available stocks
Related parts for DG528
DG528 Summary of contents
Page 1
... Each device operates with dual supplies (±4.5V to ±20V single supply (+5V to +30V). All logic inputs are TTL and CMOS compatible. The Maxim DG528/DG529 are pin and electrically compatible with the industry-standard DG528/DG529. ________________________Applications Data-Acquisition Systems ...
Page 2
... T -50 A MAX T = +25°C -10 A DG528 = 0V -200 -0.015 A MAX T = +25°C -10 A DG529 -100 -0.008 A MAX T = +25°C - 2.4V, DG528 -200 = ±10V, A MAX D = 0.8V +25°C -10 A DG529 = 2. -100 -0.015 A MAX T = +25° 2. -30 A MAX T = +25° ...
Page 3
... +25° +25° +25° 0V 1kΩ +25° 500kHz RMS T = +25° 0V 140kHz +25° 0V, DG528 T = +25°C A DG529 T = +25° +25° +25°C -1 300 180 (Note 5) 500 S ...
Page 4
... V IN SWITCH 80% OUTPUT Figure 2. Open-Time (B.B.M.) Interval Test Circuit 4 _______________________________________________________________________________________ +2.4V LOGIC INPUT 50 +2.4V t TRANSITION LOGIC INPUT 50 +2.4V +1.5V LOGIC INPUT 50 t OPEN +15V DG528 V+ IN1 EN ±10V RS IN2 TO IN7 SWITCH A0 IN8 ±10V OUTPUT A1 OUT GND WR V- 35pF 1M -15V +15V DG529 V+ IN1B ±10V EN RS ...
Page 5
... EN LOGIC INPUT IN1A TO IN4A 50 A0 IN2B, IN3B, IN4B A1 OUTB OUT GND WR +2.4V EN A0, A1 (A2) REMAINING SWITCHES RS WR OUTB OUT LOGIC 0 INPUT GND RS WR +15V DG528 V+ IN1 -5V SWITCH OUTPUT OUT 35pF 1k -15V +15V DG529 V+ IN1B -5V OUTA SWITCH OUTPUT 35pF 1k -15V ...
Page 6
... IS THE MEASURE OF VOLTAGE ERROR DUE TO O CHARGE INJECTION. THE CHARGE INJECTION IN COULOMBS Figure 6. Charge-Injection Test Circuit +3V +1. +3V +2.0V EN, A0, A1, (A2) +0.8V 0 Figure 7. Typical Timing Diagrams for DG528/DG529 6 _______________________________________________________________________________________ t OFF(RS) 0 GEN V GEN SHOWN + ...
Page 7
... No current is drawn from the negative supply, so Maxim’s MAX635 DC-DC converter is an ideal choice. The EN latch allows all switches to be turned off under program control. This is useful when two or more DG528s are cascaded to build 16-line and larger ana- log-signal multiplexers ...
Page 8
... The switching delays increase by about a factor of two at ±5V, and break- before-make action is preserved. The DG528/DG529 can operate with a single +5V to +30V supply as well as asymmetrical power supplies like +15V and -5V. The digital threshold will remain approximately 1.6V above the GND pin, and the analog ...
Page 9
... Latchable Multiplexers RESET MICROPROCESSOR SYSTEM BUS WR ADDRESS BUS ADDRESS DECODER Figure 9. Bus Interface _____________________________________________Pin Configurations (continued) TOP VIEW DG528 LCC/PLCC _______________________________________________________________________________________ +15V V+ A0 DATA BUS +5V 7432 -15V ...
Page 10
... Contact factory for availability and processing to MIL-STD-883. 10 ______________________________________________________________________________________ _________________Chip Topographies PIN-PACKAGE TRANSISTOR COUNT: 200 SUBSTRATE CONNECTED S1A S2A S3A S4A TRANSISTOR COUNT: 200 SUBSTRATE CONNECTED TO V+ DG528 GND 0.125" (3.18mm 0.131" (3.33mm) DG529 GND 0.125" (3.18mm) ...
Page 11
Latchable Multiplexers ________________________________________________________Package Information ______________________________________________________________________________________ 0° - 15° Plastic DIP PKG. PLASTIC P P DUAL-IN-LINE P PACKAGE ...
Page 12
... B S1 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied ...