MAX4735 Maxim, MAX4735 Datasheet
MAX4735
Related parts for MAX4735
MAX4735 Summary of contents
Page 1
... Each channel has a 0.31Ω typ- ical on-resistance, allowing the MAX4735 to drive 8Ω loudspeakers with less than 0.02% distortion. The MAX4735 is configured as a quad-SPDT switch with two common control inputs. Each digital input controls two pairs of SPDT switches. The switches are fully bidi- rectional, allowing both multiplexing and demultiplexing operation ...
Page 2
... Limit forward-diode current to maximum current rating. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability ...
Page 3
... Input-Logic Low V IL Input Leakage Current I IN Note 2: Devices are 100% tested Note 3: R and R matching specifications are guaranteed by design for MAX4735ETE only Note 4: ∆ ON(MAX) ON(MIN) Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance, as measured over the specified analog signal ranges ...
Page 4
... V OUT Figure 1. Switching Time MAX4735 NC_ V N_ NO_ IN_ LOGIC GND INPUT C INCLUDES FIXTURE AND STRAY CAPACITANCE. L Figure 2. Break-Before-Make Interval MAX4735 R GEN NC_ OR NO_ V GEN GND Figure 3. Charge Injection 4 _______________________________________________________________________________________ Timing Circuits/Timing Diagrams CC LOGIC CC INPUT COM_ V OUT ...
Page 5
... Figure 5. Channel On-/Off-Capacitance V OUT OFF-ISOLATION = 20log ✕ V REF V 50Ω OUT ON-LOSS = 20log ✕ V REF V OUT CROSSTALK = 20log ✕ V REF REF V REF 50Ω *FOR CROSSTALK THIS PIN IS NO2. NC2 AND COM2 ARE OPEN 10nF V CC COM_ MAX4735 IN NC_ or NO_ GND ...
Page 6
Low-Voltage, 0.31Ω, Quad-SPDT Analog Switch ( +25°C, unless otherwise noted ON-RESISTANCE vs. COM_ VOLTAGE 1.0 0.9 0 1. 1. 2.0V 0.5 CC 0.4 V ...
Page 7
Low-Voltage, 0.31Ω, Quad-SPDT Analog Switch ( +25°C, unless otherwise noted COM_ ON-CAPACITANCE vs. COM_ VOLTAGE 350 300 250 200 150 100 0.5 1.0 1.5 2.0 2.5 3.0 V (V) COM ON-RESPONSE ...
Page 8
... CMOS analog switch channels. They can be configured as dual-DPDT switches, dual 4:2 multiplexers/demulti- plexers single 8:4 multiplexer/demultiplexer. See Figure 6. Applications Information Analog Signal Range The CMOS switches in the MAX4735 function on any signal within the power-supply voltages. If any channel exceeds clamped any channel goes below GND clamped to GND by a silicon diode ...
Page 9
... For an 8Ω load, this corresponds to 2.3V . For a 4Ω load, this is 1.1V RMS The MAX4735 is offered in 16-pin TSSOP and 3mm x 3mm x 0.8mm TQFN packages. The mechanical draw- and IL ings for these packages are located at the end of this data sheet ...
Page 10
... Low-Voltage, 0.31Ω, Quad-SPDT Analog Switch Chip Information TRANSISTOR COUNT: 487 PROCESS: CMOS 10 ______________________________________________________________________________________ Pin Configurations (continued) TOP VIEW INA NC1 2 15 NC4 COM1 3 14 COM4 MAX4735 NO1 4 13 NO4 NC2 5 12 NC3 COM2 6 11 COM3 NO2 7 10 NO3 GND 8 9 INB ...
Page 11
... Low-Voltage, 0.31Ω, Quad-SPDT Analog Switch (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages 0. ______________________________________________________________________________________ D/2 E Package Information D2 0. ...
Page 12
... Low-Voltage, 0.31Ω, Quad-SPDT Analog Switch (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages.) PKG 12L 3x3 REF. MIN. NOM. MAX. MIN. 0.70 0.75 0.80 0. 0.20 0.25 0.30 0.20 D 2.90 3.00 3.10 2.90 E 2.90 3.00 3.10 2.90 e 0.50 BSC. 0.45 0.55 0.65 0. ...
Page 13
... For the latest package outline information go to www.maxim-ic.com/packages.) Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. ...