MAX9063 Maxim, MAX9063 Datasheet
MAX9063
Available stocks
Related parts for MAX9063
MAX9063 Summary of contents
Page 1
... The MAX9062, MAX9063 and MAX9064 are single com- parators with an internal 0.2V reference. These devices feature either a push-pull or an open-drain output. They consume only 700nA (max) supply current. The MAX9062, MAX9063, and MAX9064 operate down to V over the extended -40° ...
Page 2
... Comparators in 4-Bump UCSP and 5 SOT23 ABSOLUTE MAXIMUM RATINGS V , REF GND................................................-0.3V to +6V CC OUT to GND (MAX9060–MAX9063).........................-0.3V to +6V OUT to GND (MAX9064 Only) ................-0. Output Short-Circuit Current Duration ....................................10s Input Current into Any Terminal........................................±20mA Continuous Power Dissipation 4-Bump UCSP (derate 3.0mW/°C above +70°C) .......238 mW 5-Pin SOT23 (derate 3.9mW/° ...
Page 3
... Note 5: Overdrive is defined as the voltage above or below the switching points. Note 6: Guaranteed by ATE and/or bench characterization over temperature. V Note 7: Includes reference error along with comparator offset voltage error. _______________________________________________________________________________________ Ultra-Small, Low-Power Single = 3.3V for MAX9062/MAX9063 -40°C to +85°C. Typical values CONDITIONS Guaranteed by I ...
Page 4
... V = 1.8V REF 0 -40 - TEMPERATURE (°C) 4 _______________________________________________________________________________________ Typical Operating Characteristics = 3.3V for MAX9060–MAX9063, V PULLUP GND MAX9064 SUPPLY CURRENT vs. SUPPLY VOLTAGE 1000 800 +85°C +25°C 600 400 200 -40° SUPPLY VOLTAGE (V) MAX9060 AND MAX9064 OUTPUT VOLTAGE LOW vs. SINK CURRENT 1 ...
Page 5
... -40 - TEMPERATURE (°C) MAX9060 PROPAGATION DELAY AT V 1.9V 1.7V 0V _______________________________________________________________________________________ Ultra-Small, Low-Power Single Typical Operating Characteristics (continued) = 3.3V for MAX9060–MAX9063, V PULLUP MAX9064 REFERENCE VOLTAGE vs. TEMPERATURE 202 3.3V CC 201.9 201.8 201.7 201.6 201.5 201.4 201.3 201.2 201.1 201.0 -40 - TEMPERATURE (° ...
Page 6
... MAX9064 OUTPUT RESPONSE TO SUPPLY VOLTAGE TRANSIENT 3. 1ms/div 6 _______________________________________________________________________________________ Typical Operating Characteristics (continued) = 3.3V for MAX9060–MAX9063, V PULLUP MAX9060 1kHz FREQUENCY RESPONSE MAX9060 toc18 = 3.3V CC 1.9V IN+ 1.8V 50mV/div 1.7V OUT 2V/div 0V MAX9060 toc20 = 1.7V = 1.8V V REF 1V/div 0V OUT 2V/div 0V ...
Page 7
... RF noise being picked up by input traces. These devices feature an internal temperature-compensated, low-power 0.2V reference voltage. The MAX9060–MAX9063 have open-drain outputs that allow them to interface to logic circuitry running from supply voltages other than the one supplied to the part. These devices require an external pullup resistor or current source for proper operation ...
Page 8
... Additional external hysteresis is not recommended for the MAX9061 due to possible crossover current-related noise problems. Additional external hysteresis is not CC and possible on the MAX9063 because the noninverting CC input of the comparator is not externally accessible. The MAX9060 and MAX9061 can be used as an adap- tive signal-level detector. Feed a DAC output voltage to REF and connect the input to a variable signal level ...
Page 9
... MICROCONTROLLER V DD INTERNAL PULLUP 0.2V REF OUT I/O IN MICROCONTROLLER V DD OUT I/O MICROCONTROLLER PROCESS: BiCMOS OUTPUT Open drain Open drain Open drain Open drain Push-pull Typical Operating Circuits V DD INTERNAL REF MAX9061 OUT I/O IN MICROCONTROLLER V = 1. INTERNAL MAX9063 OUT I/O MICROCONTROLLER Chip Information PULLUP PULLUP 9 ...
Page 10
... Comparators in 4-Bump UCSP and 5 SOT23 For the latest package outline information and land patterns (footprints www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing per- tains to the package regardless of RoHS status ...
Page 11
... Comparators in 4-Bump UCSP and 5 SOT23 For the latest package outline information and land patterns (footprints www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing per- tains to the package regardless of RoHS status ...
Page 12
... Updated Note 6 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © ...