MAX9933 Maxim, MAX9933 Datasheet
MAX9933
Available stocks
Related parts for MAX9933
MAX9933 Summary of contents
Page 1
... RF input port. These devices feature a power-on delay when coming out of shutdown, holding OUT low for approximately 2.5µs to ensure glitch-free controller output. The MAX9930–MAX9933 family is available in an 8-pin ® µMAX package. These devices consume 7mA with a 5V supply, and when powered down, the typical shut- down current is 13µ ...
Page 2
... Voltage Range V Output-Referred Noise Small-Signal Bandwidth Slew Rate SET INPUT (MAX9930/MAX9931/MAX9932) Voltage Range (Note 2) V Input Resistance Slew Rate (Note 3) DETECTOR OUTPUT (MAX9933) Voltage Range V Small-Signal Bandwidth Slew Rate 2 _______________________________________________________________________________________ OUT Short Circuit to GND ........................................ Continuous Continuous Power Dissipation (T + 0.3V) 8-Pin µMAX (derate 4.5mW/°C above +70°C) .............362mW CC Operating Temperature Range ...........................-40° ...
Page 3
... MAX9931 T = +25°C A MAX9932 MAX9930/MAX9933 f = 2MHz MAX9931 RF MAX9932 MAX9930/MAX9933 f = 900MHz MAX9931 +25°C A MAX9932 MAX9930/MAX9933 f = 900MHz MAX9931 RF MAX9932 MAX9930/MAX9933 f = 1600MHz MAX9931 RF MAX9932 Connected Internally DC-coupled (Note +25°C and are guaranteed by design for T A MIN TYP MAX UNITS ...
Page 4
RF-Detecting Controllers and RF Detector = 3V, SHDN = +25°C, all log conformance plots are normalized to their respective temperatures otherwise noted.) MAX9930 SET vs. INPUT POWER ...
Page 5
RF-Detecting = 3V, SHDN = +25°C, all log conformance plots are normalized to their respective temperatures otherwise noted.) MAX9930 LOG INTERCEPT vs -57 -59 2MHz ...
Page 6
RF-Detecting Controllers and RF Detector = 3V, SHDN = +25°C, all log conformance plots are normalized to their respective temperatures otherwise noted.) MAX9931 LOG SLOPE vs. V ...
Page 7
... V (V) CC MAX9932 LOG CONFORMANCE vs. TEMPERATURE 0.1 INPUT POWER = -10dBm f = 50MHz RF 0 -0.1 -0.2 -0.3 -0.4 -0.5 -50 - 5.0 5.5 TEMPERATURE (°C) MAX9933 OUTPUT AND LOG CONFORMANCE vs. INPUT POWER AT 2MHz 1.8 1.6 1.4 1.2 1.0 0 +85° +25° -40° -60 -50 -40 -30 -20 INPUT POWER (dBm) CC 5.0 5.5 75 100 ...
Page 8
... INPUT POWER (dBm) MAX9933 LOG SLOPE vs 1.6GHz 28 27 50MHz 26 900MHz 25 2MHz 2.5 3.0 3.5 4.0 4.5 5.0 V (V) CC MAX9933 LOG CONFORMANCE vs. TEMPERATURE 0.4 INPUT POWER = -22dBm f = 50MHz RF 0.3 0.2 0.1 0 -0.1 -0.2 -50 - TEMPERATURE (°C) = +25°C, unless A MAX9933 OUTPUT AND LOG CONFORMANCE vs. INPUT POWER AT 1.6GHz 1 ...
Page 9
... CLPF OUT 500mV/div RFIN 250mV/div -42dBm 10μs/div _______________________________________________________________________________________ Controllers and RF Detector Typical Operating Characteristics (continued) SHDN 500mV/div 1V/div 4.0 4.5 5.0 5.5 MAIN OUTPUT NOISE-SPECTRAL DENSITY 10,000 MAX9933 CLPF = 220pF 0V 1000 0V 100 100 1k 10k 100k FREQUENCY (Hz) MAX9930 toc51 ≤ 900mV 75mV/div f = 50MHz RF 25mV/div -2dBm = +25° ...
Page 10
... DET DET DET DET 10dB 10dB 10dB 10dB OFFSET REFERENCE COMP CURRENT OUTPUT- ENABLED DELAY DET DET DET DET 10dB 10dB 10dB 10dB OFFSET REFERENCE COMP CURRENT Pin Description FUNCTION g X1 OUT m CLPF V-I* SET MAX9930 MAX9931 MAX9932 g X1 OUT m CLPF V-I* MAX9933 ...
Page 11
... Logarithmic slope and intercept determine the transfer function of the MAX9930–MAX9933 family of log amps. The change in SET voltage (OUT voltage for the MAX9933) per dB change in RF input defines the loga- rithmic slope. Therefore, a 10dB change in RF input results in a 250mV change at SET (OUT for the MAX9933) ...
Page 12
... GND for PA control inputs that source current. The Typical Operating Characteristics has the Maximum Out Voltage vs. V sourcing capabilities and output swing of OUT. The MAX9930–MAX9933 can be placed in shutdown by pulling SHDN to ground. Shutdown reduces supply cur- rent to typically 13µA. A graph of SHDN Response Time is included in the Typical Operating Characteristics . ...
Page 13
... AC-coupling capacitor at RFIN as shown in Figure 5. A 50Ω resistor (use other values for different input imped- ances) in this configuration, in parallel with the input impedance of the MAX9930–MAX9933, presents an , domi- CLPF input impedance of approximately 50Ω. These devices require an additional external coupling capacitor in series with the RF input ...
Page 14
... Layout Considerations As with any RF circuit, the layout of the MAX9930– MAX9933 circuits affects performance. Use a short 50Ω line at the input with multiple ground vias along the length of the line. The input capacitor and resistor should both be placed as close as possible to the IC. ...
Page 15
... RF-Detecting For the latest package outline information and land patterns www.maxim-ic.com/packages. PACKAGE TYPE 8 µMAX ______________________________________________________________________________________ Controllers and RF Detector Package Information PACKAGE CODE U8-1 α α DOCUMENT NO. 21-0140 15 ...
Page 16
... Added TOC46 to Typical Operating Characteristics Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 16 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © ...