MAX9002 Maxim, MAX9002 Datasheet
MAX9002
Available stocks
Related parts for MAX9002
MAX9002 Summary of contents
Page 1
... The amplifiers in the MAX9000/MAX9001/MAX9002 are unity-gain stable with a 1.25MHz gain-bandwidth product, while the amplifiers in the MAX9003/MAX9004/MAX9005 are stable for closed-loop gains of +10V/V or greater with an 8MHz gain-bandwidth product ...
Page 2
... Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS SHDN = +2.5V to +5.5V MAX9001/MAX9002/MAX9004/MAX9005), COUT = low and T = +25°C PARAMETER SYMBOL Supply Voltage Range ...
Page 3
... Low-Power, High-Speed, Single-Supply Op Amp + Comparator + Reference ICs ELECTRICAL CHARACTERISTICS (continued SHDN = +2.5V to +5.5V MAX9001/MAX9002/MAX9004/MAX9005), COUT = low and T = +25°C PARAMETER SYMBOL Large-Signal Voltage Gain A VOL Output Voltage Swing Gain-Bandwidth Product GBW Phase Margin Gain Margin ...
Page 4
... Power-On Time Capacitive Load Stability Note 1: Comparator Input Offset is defined as the center of the input-referred hysteresis zone. Note 2: Measured for the MAX9001/MAX9002/MAX9004/MAX9005 CM(COMP) Note 3: Input-referred hysteresis is defined as the difference of the trip points required to change comparator output states. Note the overdrive that is beyond the offset and hysteresis-determined trip points. ...
Page 5
... SUPPLY VOLTAGE (V) MAX9000/MAX9001/MAX9003/MAX9004 SUPPLY CURRENT vs. TEMPERATURE 500 V = 5.5V 450 DD 400 V = 2.5V DD 350 300 -40 - TEMPERATURE (°C) MAX9002/MAX9005 SUPPLY CURRENT vs. TEMPERATURE 500 450 400 V = 5.5V DD 350 V = 2.5V DD 300 -40 - TEMPERATURE (°C) _______________________________________________________________________________________ , COUT = low SHUTDOWN SUPPLY CURRENT vs ...
Page 6
Low-Power, High-Speed, Single-Supply Op Amp + Comparator + Reference ICs ____________________________________Typical Operating Characteristics (continued) (op amp SHDN = +5V CHANGE IN OP-AMP OFFSET VOLTAGE (V OS vs. SUPPLY ...
Page 7
... 10k 100k 100 200 300 400 500 600 700 800 900 1000 C (pF) LOAD MAX9000/MAX9001/MAX9002 OP-AMP POWER-SUPPLY REJECTION vs. FREQUENCY LOAD -20 -40 -60 -80 -100 100 1k 10k 100k 1M 10M FREQUENCY (Hz) MAX9003/MAX9004/MAX9005 OP-AMP POWER-SUPPLY REJECTION vs. FREQUENCY ...
Page 8
... AOUT CHANGE IN COMPARATOR OFFSET VOLTAGE (V ) vs. TEMPERATURE OS 200 150 100 50 0 -50 -100 -150 -200 -40 - 100 TEMPERATURE (°C) MAX9000/MAX9001/MAX9002 OP-AMP OUTPUT IMPEDANCE vs. FREQUENCY LOAD 100 10 1 0.1 0.01 100 1k 10k 100k 1M 10M FREQUENCY (Hz) MAX9003/MAX9004/MAX9005 OP-AMP OUTPUT IMPEDANCE vs. FREQUENCY 10k A ...
Page 9
Low-Power, High-Speed, Single-Supply Op Amp + Comparator + Reference ICs _____________________________Typical Operating Characteristics (continued) (op amp SHDN = +5V COMPARATOR HYSTERESIS vs. TEMPERATURE 3.5 3.2 2.9 2.6 2.3 ...
Page 10
... A V OUTPUT VOLTAGE CHANGE REF vs. SUPPLY VOLTAGE 100 50 0 -50 -100 2.5 3.0 3.5 4.0 4.5 5.0 5.5 SUPPLY VOLTAGE (V) V 0.1Hz to 10Hz VOLTAGE NOISE REF 5 V/div 1sec/div MAX9000/MAX9001/MAX9002 OP-AMP SMALL-SIGNAL TRANSIENT RESPONSE WITH C LOAD 270pF 50mV/div V OUT 50mV/div 1 s/div V LOAD-TRANSIENT RESPONSE REF +1mA I OUT -1mA ...
Page 11
... COUT = low MAX9000/MAX9001/MAX9002 OP-AMP LARGE-SIGNAL TRANSIENT RESPONSE LOAD 5V/div 4V V OUT 1V/div 0V 2 s/div NAME 14 SO SHDN AOUT 3 4 AIN AIN+ ...
Page 12
... DD ages. The comparator’s inverting input is internally con- nected to the reference output in the MAX9000/MAX9003. COUT 7 The MAX9002/MAX9005 do not have an internal refer- COMP ence, but the inverting input of the comparator is avail- able externally. The MAX9001/MAX9004 include both the CIN+ 6 inverting input and the reference output. The MAX9000/ MAX9001/MAX9003/MAX9004 typically consume only 410µ ...
Page 13
... To compensate for this effect, place a 2pF to 10pF capacitor across the feedback resistor, as shown in Figure 5. .). For single Figure 2. Isolation Resistors to Drive Capacitive Loads Op-Amp Frequency Stability LOAD MAX9000 MAX9001 MAX9002 LOAD R MAX9003 MAX9004 MAX9005 13 ...
Page 14
... V IN 50mV/ div V OUT 50mV/ div Figure 4. MAX9000/MAX9001/MAX9002 Op-Amp Small-Signal Transient Response with Capacitive Load (C = 510pF) and L No Isolation Resistor AOUT Figure 6. External Hysteresis comparator. The outputs do not undergo phase rever- ...
Page 15
Low-Power, High-Speed, Single-Supply Op Amp + Comparator + Reference ICs To add hysteresis, use the following procedure: Step 1: The device’s input bias current can be as high as 80nA. To minimize error due to the input bias, choose a ...
Page 16
Low-Power, High-Speed, Single-Supply Op Amp + Comparator + Reference ICs antenna can be long parallel wires spaced about 7.2cm apart, with equal but opposite currents. Radio waves from this antenna are detectable when the receiver is brought within close proximity, ...
Page 17
... TOP VIEW AOUT AIN COUT MAX9000 MAX9002 AIN CIN+ MAX9003 MAX9005 REF (CIN-) SS SO/ MAX ( ) ARE FOR THE MAX9002/MAX9005. ______________________________________________________________________________________ SHDN AOUT 2 9 COUT MAX9001 AIN CIN+ MAX9004 AIN CIN REF ...
Page 18
... Low-Power, High-Speed, Single-Supply Op Amp + Comparator + Reference ICs Ordering Information (continued) PART TEMP. RANGE MAX9002EUA -40°C to +85°C MAX9002ESA -40°C to +85°C MAX9003EUA -40°C to +85°C MAX9003ESA -40°C to +85°C MAX9004EUB -40°C to +85°C MAX9004ESD -40°C to +85°C MAX9005EUA -40°C to +85°C MAX9005ESA -40° ...
Page 19
Low-Power, High-Speed, Single-Supply Op Amp + Comparator + Reference ICs ______________________________________________________________________________________ Package Information (continued) 19 ...
Page 20
... Op Amp + Comparator + Reference ICs Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied ...