MAX9943 Maxim, MAX9943 Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
MAX9943
Manufacturer Part Number
MAX9943
Description
The MAX9943/MAX9944 is a family of high-voltage amplifiers that offers precision, low drift, and low power consumption
Manufacturer
Maxim
Datasheet
1.MAX9943.pdf
(15 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
MAX9943AUA
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
MAX9943AUA+
Manufacturer:
Maxim Integrated Products
Quantity:
1 940
Part Number:
MAX9943AUA+
Manufacturer:
MAXIM/美信
Quantity:
20 000
High-Voltage, Precision, Low-Power Op Amps
The MAX9943/MAX9944 can operate with dual supplies
from ±3V to ±19V or with a single supply from +6V to
+38V with respect to ground. When used with dual sup-
plies, bypass both V
capacitor to ground. When used with a single supply,
bypass V
layout technique helps optimize performance by
decreasing the amount of stray capacitance at the op
amp’s inputs and outputs. To decrease stray capaci-
tance, minimize trace lengths by placing external com-
ponents close to the op amp’s pins.
The MAX9943/MAX9944 are capable of driving heavy
loads such as the ones that can be found in loop-pow-
ered systems for remote sensors. The information is
transmitted through ±20mA or 4mA–20mA current output
across long lines that are terminated with low resistance
loads (e.g., 600Ω). The Typical Application Circuit shows
the MAX9944 used as a voltage-to-current converter with
a current-sense amplifier in the feedback loop. Because
of the high output current capability of the MAX9944, the
device can be used to directly drive the current-loop.
The specifications and operation of the MAX9943/
MAX9944 family is guaranteed over the -40°C to
+125°C temperature range, However, when used in
applications with ±15V supply voltage (see Figure 3),
the capability of driving more than ±20mA of current is
limited to the -40°C to +85°C temperature range. Use a
lower supply voltage if this current must be delivered at
a higher temperature range.
The MAX9943/MAX9944 input common-mode range
can swing to the negative rail V
can swing to both the positive V
V
two features are very important for applications where
the MAX9943/ MAX9944 are used with a single-supply
(V
can benefit from these features is when the single-sup-
ply op amp is driving an ADC.
8
EE
EE
_______________________________________________________________________________________
rails if the output stage is not heavily loaded. These
connected to ground). One of the applications that
Input Common Mode and Output Swing
CC
with a 0.1μF capacitor to ground. Careful
Power Supplies and Layout
CC
Output Current Capability
and V
EE
EE
CC
with their own 0.1μF
. The output voltage
and the negative
During normal op-amp operation, the inverting and non-
inverting inputs of the MAX9943/MAX9944 are at essen-
tially the same voltage. However, either due to fast
input voltage transients or due to other fault conditions,
these pins can be forced to be at two different voltages.
Internal back-to-back diodes and series resistors pro-
tect the inputs from an excessive differential voltage
(see Figure 2). Therefore, IN+ and IN- can be any volt-
age within the range shown in the absolute maximum
rating. Note the protection time is still dependent on the
package thermal limits.
PROCESS: BiCMOS
Figure 1. Capacitive Load Driving Circuit
Figure 2. Input Protection Circuit
INPUT
Input Differential Voltage Protection
1.5kΩ
1.5kΩ
MAX9943
Chip Information
R
ISO
C
L
OUTPUT