MAX4284 Maxim, MAX4284 Datasheet - Page 11

• Manufacturer Part Number: MAX4284
• Description: The MAX4174/MAX4175/MAX4274/MAX4275 GainAmp family combines a low-cost rail-to-rail op amp with precision internal gain-setting resistors and VCC/2 biasing
• Manufacturer: Maxim

Maxim’s GainAmp fixed-gain amplifiers combine a low-
cost rail-to-rail op amp with internal gain-setting resis-
tors. Factory-trimmed on-chip resistors provide 0.1%
gain accuracy while decreasing design size, cost, and
layout. Three versions are available in this amplifier
family: single/dual/quad open-loop, unity-gain-stable
devices (MAX4281/MAX4282/MAX4284); single/dual
fixed-gain devices (MAX4174/MAX4274); and single/
dual devices with fixed gain plus internal V
at the noninverting input (MAX4175/MAX4275). All
amplifiers feature rail-to-rail outputs and drive a 1k Ω
load while maintaining excellent DC accuracy.
The single/dual/quad MAX4281/MAX4282/MAX4284
are high-performance, open-loop op amps with rail-to-
rail outputs. These devices are compensated for unity-
gain stability, and feature a gain bandwidth (GBW) of
2MHz. The op amps in these ICs feature an input com-
mon-mode range that extends from 150mV below the
negative rail to within 1.2V of the positive rail. These
high performance op amps serve as the core for this
family of GainAmp fixed-gain amplifiers. Although the
-3dB bandwidth will not correspond to that of a fixed-
gain amplifier in higher gain configurations, these
open-loop op-amps can be used to prototype designs.
Maxim’s proprietary laser trimming techniques produce
the necessary R
offerings are easily available. These GainAmp fixed-gain
amplifiers feature a negative-feedback resistor network
that is laser trimmed to provide a gain-setting feedback
ratio (R
op amp pinouts allow the GainAmp fixed-gain amplifiers
to drop in directly to existing board designs, easily
replacing op-amp-plus-resistor gain blocks.
GainAmp fixed-gain amplifiers feature factory-trimmed
precision resistors to provide fixed inverting gains from
-0.25V/V to -100V/V or noninverting gains from
+1.25V/V to +101V/V. The op-amp core is decompen-
sated strategic ally over the gain-set options to maxi-
mize bandwidth. Open-loop decompensation increases
GBW product, ensuring that usable bandwidth is main-
tained with increasing closed-loop gains. A GainAmp
with a fixed gain of A
of 230kHz. By comparison, a unity-gain-stable op amp
configured for A
width of only 20kHz (Figure 2). Decompensation is per-
formed at five intermediate gain sets, as shown in the
Gain Selection Guide . Low gain decompensation great-
F
/R
G
) with 0.1% typical accuracy. The standard
Internal Gain-Setting Resistors
V
F
/R
______________________________________________________________________________________
= 100V/V would yield a -3dB band-
G
V
values (Figure 1), so many gain
Detailed Description
= 100V/V has a -3dB bandwidth
GainAmp Bandwidth
Open-Loop Op Amps
GainAmps/Open-Loop Op Amps
SOT23, Rail-to-Rail, Fixed-Gain
CC
/ 2 bias
ly increases usable bandwidth, while decompensation
above gains of +25V/V offers diminished returns.
The MAX4175/MAX4275 GainAmp fixed-gain amplifiers
with the V
GainAmp fixed-gain amplifiers, with the added feature
of V
150kΩ resistors form a voltage-divider for self-biasing
the noninverting input, eliminating external bias resis-
tors for AC-coupled applications, and allowing maxi-
mum signal swing at the op amp’s rail-to-rail output for
single-supply systems (see Typical Operating Circuit ).
For DC-coupled applications, use the MAX4174/
MAX4274.
The MAX4174/MAX4175/MAX4274/MAX4275 include
±17V input fault protection. For normal operation, see
the input voltage range specification in the
Characteristics . Overdriven inputs up to ±17V will not
Figure 1. Internal Gain-Setting Resistors
Figure 2. Gain-Bandwidth Comparison
High-Voltage (±17V) Input Fault Protection
IN+
CC
IN-
/ 2 internal bias at the noninverting inputs. Two
CC
-3dB
R
60
50
40
30
20
10
G
0
/ 2 bias option are identical to standard
10
V
V
CC
EE
100
R
1k
F
20kHz
FREQUENCY (Hz)
230kHz
10k
V
CC
100k
MAX4281, A
2MHz GBW
/ 2 Internal Bias
1M
MAX4174,
A
23MHz GBW
V
= 100
10M
V
= 100
A
A
V
V
=
= 1 +
-R
Electrical
R
F
G
R
R
OUT
F
G
11