MAX4165 Maxim, MAX4165 Datasheet
MAX4165
Available stocks
Related parts for MAX4165
MAX4165 Summary of contents
Page 1
... No Phase Reversal for Overdriven Inputs ♦ Unity-Gain Stable for Capacitive Loads to 250pF ♦ Low-Power Shutdown Mode: Reduces Supply Current to 38µA Places Outputs in High-Impedance State ♦ Available in 5-Pin SOT23 Package (MAX4165) or 2mm x 2mm x 0.8mm µDFN (MAX4166) SHUTDOWN MODE PART — ...
Page 2
... Note 1: Continuous power dissipation should also be observed. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability ...
Page 3
High-Output-Drive, Precision, Low-Power, Single- Supply, Rail-to-Rail I/O Op Amps with Shutdown DC ELECTRICAL CHARACTERISTICS (continued +2.7V to +6. noted.) PARAMETER SYMBOL Output Voltage Swing V OUT Output Source/Sink ...
Page 4
... Note 2: Although the minimum output current is guaranteed to be ±80mA, exercise caution to ensure that the absolute maximum power-dissipation rating of the package is not exceeded. Note 3: SHDN logic thresholds are referenced to V Note 4: The MAX4165EUK is 100% tested at +25°C. All temperature limits are guaranteed by design. AC ELECTRICAL CHARACTERISTICS ( ...
Page 5
... +6.5V +2.7V - +6.5V -40 -60 -40 - TEMPERATURE (°C) POWER-SUPPLY REJECTION RATIO vs. FREQUENCY MAX4165-02 216 VCL 180 0 144 -10 -20 108 72 -30 - -50 -60 -36 -72 -70 -108 -80 -144 -90 10M 100 1k 10k 100k FREQUENCY (Hz) SHUTDOWN SUPPLY CURRENT PER AMPLIFIER vs ...
Page 6
High-Output-Drive, Precision, Low-Power, Single- Supply, Rail-to-Rail I/O Op Amps with Shutdown ____________________________Typical Operating Characteristics (continued +5.0V 0V 100kΩ MINIMUM OPERATING VOLTAGE vs. TEMPERATURE 2.00 1.95 1.90 1.85 1.80 1.75 -40 ...
Page 7
... PEAK-TO-PEAK OUTPUT VOLTAGE 250 0 10kHz R = 100k 0.001 100k 4.0 4.2 4.4 4.6 PEAK-TO-PEAK OUTPUT (V) SMALL-SIGNAL TRANSIENT RESPONSE (INVERTING) MAX4165- -1V/V VCL IN (50mV/div) OUT (50mV/div) TIME (500ns/div) LARGE-SIGNAL TRANSIENT RESPONSE (INVERTING) MAX4165- -1V/V VCL IN (2V/div) OUT (2V/div) TIME (5 s/div 4.8 5.0 MAX4165-21 7 ...
Page 8
... High-Output-Drive, Precision, Low-Power, Single- Supply, Rail-to-Rail I/O Op Amps with Shutdown PIN MAX4166 MAX4165 MAX4167 DIP/SO DFN MAX — — — — — — — — — — — — — — ...
Page 9
... PEAK RMS RMS _______________________________________________________________________________________ V = 3Vp-p IN COS to V Figure 1. A Circuit Example where the MAX4165/MAX4166 is CC OUT Being Used in Single-Supply Operation to V OUT 3Vp 189 . RMS Figure 2. A Circuit Example where Adding a Coupling ...
Page 10
... Figure 3. Dual MAX4167/MAX4168 Bridge Amplifier for 200mW at 3V Single-Supply Speaker Driver The MAX4165/MAX4166 can be used as a single-sup- ply speaker driver, as shown in the Typical Operating Circuit . Capacitor C1 is used for blocking DC (a 0.1µF ceramic capacitor can be used). When choosing resis- tors R3 and R4, take into consideration the input bias current as well as how much supply current can be tol- erated ...
Page 11
... Figure 7 shows the input voltage range EE and the output voltage swing of a MAX4165 connected as a voltage follower. The maximum output voltage swing is load dependent; however guaranteed to be within 430mV of the positive rail (V with maximum load (25Ω to ground). ...
Page 12
... Figure 9. Small-Signal Transient Response with Excessive Capacitive Load Figure 11. Capacitive-Load-Driving Circuit The MAX4165–MAX4169 can operate from a single +2.7V to +6.5V supply, or from dual ±1.35V to = +5V), the ±3.25V supplies. For single-supply operation, bypass CC the power supply with a 0.1µF ceramic capacitor in parallel with at least 1µ ...
Page 13
High-Output-Drive, Precision, Low-Power, Single- Supply, Rail-to-Rail I/O Op Amps with Shutdown SHDN (1V/div) OUT (1V/div) TIME (5 s/div) Figure 12. Shutdown Output Voltage Enable/Disable V CC (1V/div) OUT (2V/div) TIME (5 s/div) Figure 14. Power-Up/Down Output Voltage ______________________________________________________________________________________ SHDN (1V/div) ...
Page 14
High-Output-Drive, Precision, Low-Power, Single- Supply, Rail-to-Rail I/O Op Amps with Shutdown TOP VIEW N. IN MAX4166 DIP/SO/ MAX OUT1 1 IN1- 2 IN1+ 3 MAX4168 N.C. ...
Page 15
... Ordering Information (continued) PART MAX4167EPA MAX4167ESA MAX4168EPD MAX4168ESD C2 MAX4168EUB MAX4169EPD MAX4169ESD ___________________Chip Information 32 Ω MAX4165 TRANSISTOR COUNT: 230 MAX4166 TRANSISTOR COUNT: 230 MAX4167 TRANSISTOR COUNT: 462 MAX4168 TRANSISTOR COUNT: 462 MAX4169 TRANSISTOR COUNT: 924 BOTTOM VIEW ...
Page 16
... High-Output-Drive, Precision, Low-Power, Single- Supply, Rail-to-Rail I/O Op Amps with Shutdown (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information go to www.maxim-ic.com/packages Ø 0.50±0.1 0.6±0.1 1 0.6±0.1 TOP VIEW ...
Page 17
... L1022-1 -DRAWING NOT TO SCALE- Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 17 © ...