MAX9135GHJ+ Maxim Integrated Products, MAX9135GHJ+ Datasheet - Page 9
![no-image](/images/manufacturer_photos/0/4/417/maxim_integrated_products_sml.jpg)
MAX9135GHJ+
Manufacturer Part Number
MAX9135GHJ+
Description
IC SW LVDS CROSSBAR 32TQFP-EP
Manufacturer
Maxim Integrated Products
Type
LVDS Crossbar Switchr
Datasheet
1.MAX9134GHJ.pdf
(20 pages)
Specifications of MAX9135GHJ+
Applications
Digital Video
Mounting Type
Surface Mount
Package / Case
*
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Figure 1. I
The MAX9132/MAX9134/MAX9135 high-speed, multi-
ple-port, low-voltage differential signaling (LVDS)
crossbar switches are specially designed for digital
video and camera signal transmission. These switches
have a wide bandwidth, supporting data rates up to
840Mbps. This allows the use of MAX9132/MAX9134/
MAX9135 with LVDS serializers/deserializers (SerDes)
to create a complete video or camera network. The
MAX9132 has three input ports and two output ports,
the MAX9134 has three input ports and four output
ports, and the MAX9135 has four input ports and three
output ports. The video or camera signal can go
through the switch from an input port to one or multiple
output ports.
The MAX9132/MAX9134/MAX9135 switch routing is
programmable through either an I
Local Interconnect Network (LIN) serial interface. AS0
and AS1 set the slave addresses for either of these
modes, allowing several devices on a bus simultane-
ously. In addition, the MAX9134/MAX9135 provide
3-level pins S[5:0] to set switch routing and the initial
conditions for I
all the LVDS outputs feature selectable preemphasis.
Table 1. Register Address Map
ADDRESS (HEX)
REGISTER
SDA
SCL
0x00
0x01
0x02
0xFF
2
t
C Serial-Interface Timing Details
HD:STA
CONDITION
START
2
C mode. To improve the signal integrity,
_______________________________________________________________________________________
WRITE
READ/
Detailed Description
R/W
R/W
t
LOW
W
Input/Output LVDS Crossbar Switches
R
Programmable, High-Speed, Multiple
t
R
t
HIGH
LIN Status Register
Switch Control Register 1
Switch Control Register 2 (MAX9134/MAX9135
only)
Reserved
t
SU:DAT
t
F
2
LIN INTERFACE DESCRIPTION
C interface or a
t
HD:DAT
t
SU:STA
START CONDITION
On power-up, all control registers have a value of 0x00.
For the MAX9134/MAX9135, leaving S[5:0] unconnect-
ed, allows control through the LIN interface with all out-
puts deactivated. Otherwise, the switch runs in
pin-control mode with S[5:0] controlling the switch rout-
ing. The I
control mode. Successful routing through I
the pin settings. For more details, see the I
section. For the MAX9132, the FS input determines
which interface is active.
There are four 1-byte control registers in the
MAX9132/MAX9134/MAX9135. These registers control
the routing of the switch. Table 1 describes the register
map for both I
MAX9134/MAX9135 operate in LIN mode, register 0x00
acts as an error flag register. Its function is described
in detail in Table 5. In either I
trol registers (0x01, 0x02) program the MAX9132/
MAX9134/MAX9135 switch routing control. In addition,
these registers can individually activate and deactivate
preemphasis for each output port. Table 2a describes
the routing for the MAX9132/MAX9134 and Table 2b for
the MAX9135. For I
trols the activation of routing.
REPEATED
t
HD:STA
2
C is also active while the device is in pin-
Reserved
Switch Control Register 1
Switch Control Register 2 (MAX9134/MAX9135
only)
Route Activation Register
2
C and LIN. When the MAX9132/
2
C programming, register 0xFF con-
t
SU:STO
I
2
C DESCRIPTION
Register Description
2
C or LIN mode, the con-
CONDITION
STOP
Initial Power-Up
t
BUF
CONDITION
2
2
START
C overrides
C Interface
9