VIPER17 STMicroelectronics, VIPER17 Datasheet - Page 15

no-image

VIPER17

Manufacturer Part Number
VIPER17
Description
VIPerPlus family: fixed frequancy high performance off line high voltage converter
Manufacturer
STMicroelectronics
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
VIPER17
Manufacturer:
ST
0
Part Number:
VIPER17A
Manufacturer:
ST
0
Part Number:
VIPER17H
Manufacturer:
ST
0
Part Number:
VIPER17H
Manufacturer:
ST
Quantity:
20 000
Part Number:
VIPER17HD
Manufacturer:
ST
0
Part Number:
VIPER17HD
Manufacturer:
ST
Quantity:
20 000
Part Number:
VIPER17HDTR
Manufacturer:
MITSUBISHI
Quantity:
2 944
Part Number:
VIPER17HDTR
Manufacturer:
ST
0
Part Number:
VIPER17HDTR
Manufacturer:
ST
Quantity:
20 000
Part Number:
VIPER17HDTR
0
Part Number:
VIPER17HN
Manufacturer:
DIODES
Quantity:
21 400
Part Number:
VIPER17HN
Manufacturer:
STMicroelectronics
Quantity:
1 970
Part Number:
VIPER17HN
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
VIPER17HN
Quantity:
15 000
Part Number:
VIPER17L
Manufacturer:
ST
Quantity:
20 000
VIPER17
7.3
Power-up and soft-start up
If the input voltage rises up till the device start threshold, V
begins to grow due to the I
high voltage start up circuit. If the V
page
See
The IC is powered by the energy stored in the capacitor on the VDD pin, C
the self-supply circuit (typically an auxiliary winding of the transformer and a steering diode)
develops a voltage high enough to sustain the operation.
C
value higher than V
switching operation before the controller receives any energy from the auxiliary winding.
The following formula can be used for the V
Equation 1
The t
estimated by applicator according to the output stage configurations (transformer, output
capacitances, etc.).
During the converter start up time, the drain current limitation is progressively increased to
the maximum value. In this way the stress on the secondary diode is considerably reduced.
It also helps to prevent transformer saturation. The soft-start time lasts 8.5 ms and the
feature is implemented for every attempt of start up converter or after a fault.
Figure 22. I
VDD
Figure 23 on page
SSaux
6) the power MOSFET starts switching and the HV current generator is turned OFF.
capacitor must be sized enough to avoid fast discharge and keep the needed voltage
is the time needed for the steady state of the auxiliary voltage. This time is
I
DDch
DD
V
(-3 mA)
DRAIN
V
V
V
V
V
V
current during start-up and burst mode
FBbm
DDoff
V
FBolp
I
I
I
DDon
FBlin
DD
DD1
DD0
DD
START- UP
FB
DDoff
16.
threshold. In fact, a too low capacitance value could terminate the
DDch
NORMAL MODE
Doc ID 14419 Rev 7
current (see
C
DD
VDD
voltage reaches V
=
----------------------------------------
V
I
DD
DDch
DDon
Table 7 on page
capacitor calculation:
×
BURST MODE
t
V
SSaux
DDoff
DDon
DRAIN_START
6) coming from the internal
threshold (see
Operation descriptions
, the V
NORMAL MODE
VDD
t
t
t
t
V
FBbmhys
Table 7 on
DD
, until when
voltage
15/31

Related parts for VIPER17