VIPER28 STMicroelectronics, VIPER28 Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
VIPER28
Manufacturer Part Number
VIPER28
Description
VIPerPlus family: fixed frequency high performance off line high voltage converter
Manufacturer
STMicroelectronics
Datasheet
1.VIPER28.pdf
(32 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
VIPER28H
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
VIPER28HE
Manufacturer:
STM
Quantity:
2 000
Part Number:
VIPER28HN
Manufacturer:
ST
Quantity:
20 000
Part Number:
VIPER28L
Manufacturer:
ST
Quantity:
20 000
Company:
Part Number:
VIPER28LE
Manufacturer:
ROHM
Quantity:
893
Company:
Part Number:
VIPER28LN
Manufacturer:
STMicroelectronics
Quantity:
500
Part Number:
VIPER28LN
Manufacturer:
ST
Quantity:
20 000
Operation descriptions
7.7
7.8
18/32
Current mode conversion with adjustable current limit set
point
The device is a current mode converter: the drain current is sensed and converted in voltage
that is applied to the non inverting pin of the PWM comparator. This voltage is compared
with the one on the feed-back pin through a voltage divider on cycle by cycle basis.
The
the electrical specification, by the R
page
The CONT pin has a minimum current sunk needed to activate the I
R
Table 8 on page
Overvoltage protection (OVP)
The VIPER28 has integrated the logic for the monitor of the output voltage using as input
signal the voltage V
the voltage from the auxiliary winding tracks the output voltage, through the turn ratio
The CONT pin has to be connected to the auxiliary winding through the diode D
resistors R
the voltage V
on page
the auto-restart mode.
In order to bypass the noise immediately after the turn off of the power MOSFET, the voltage
V
the
digital signal and increments the internal counter. The same counter is reset every time the
signal OVP is not triggered in one oscillator cycle.
Referring to the
Equation 2
Equation 3
N
--------------
N
CONT
LIM
AUX
SEC
Figure 26 on page
VIPER28
or with high R
11.
is sampled inside a short window after the time T
7) the overvoltage protection will stop the power MOSFET and the converter enters
OVP
CONT
has a default current limit value, I
and R
Figure
7).
exceeds, four consecutive times, the reference voltage V
LIM
CONT
LIM
(i.e. 100 kΩ) the current limit is fixed to the default value (see I
19. The sampled signal, if higher than V
17, the resistors divider ratio k
as shows the
k
during the OFF time of the power MOSFET. This is the time when
OVP
=
Doc ID 15028 Rev 4
-------------------------------------------------------------------------------------------------- -
N
--------------
N
AUX
SEC
LIM
k
OVP
⋅
Figure 27 on page 20
resistor connected to the CONT see
(
V
=
OUTOVP
--------------------------------- -
R
LIM
Dlim
V
R
OVP
+
LIM
+
, that the designer can adjust according
R
V
OVP
DSEC
OVP
STROBE
) V
will be given by:
–
When, during the OFF time,
DAUX
OVP
, see
, trigger the internal OVP
Dlim
Table 8 on page 7
adjustment: without
OVP
Figure 16 on
(see
OVP
VIPER28
and the
Table 8
Dlim
and
,