EP4SGX530NF45C3 Altera Corporation, EP4SGX530NF45C3 Datasheet - Page 56

• Manufacturer Part Number: EP4SGX530NF45C3
• Description: IC STRATIX IV FPGA 530K 1932FBGA
• Manufacturer: Altera Corporation
• Series: Stratix® IV GXr

Specifications of EP4SGX530NF45C3

• Number Of Logic Elements/cells: 531200
• Number Of Labs/clbs: 21248
• Total Ram Bits: 28033024
• Number Of I /o: 920
• Number Of Gates: -
• Voltage - Supply: 0.87 V ~ 0.93 V
• Mounting Type: Surface Mount
• Operating Temperature: 0°C ~ 85°C
• Package / Case: 1932-BBGA
• Lead Free Status: Contains lead
• Rohs Status: RoHS non-compliant

1–48
Table 1–34. PLL Specifications for Stratix IV Devices (Part 2 of 2)—Preliminary
Stratix IV Device Handbook Volume 4: Device Datasheet and Addendum
t
t
t
t
f
Notes to
(1) This specification is limited in the Quartus II software by the I/O maximum frequency. The maximum I/O frequency is different for each I/O
(2) The VCO frequency reported by the Quartus II software in the PLL summary section of the compilation report takes into consideration the VCO
(3) This specification is limited by the lower of the two: I/O F
(4) A high input jitter directly affects the PLL output jitter. To have low PLL output clock jitter, you must provide a clean clock source that is less
(5) F
(6) Peak-to-peak jitter with a probability level of 10
(7) The cascaded PLL specification is only applicable with the following condition:
(8) High bandwidth PLL settings are not supported in external feedback mode.
(9) External memory interface clock output jitter specifications use a different measurement method, which is available in
OUTCCJ_DC
OUTPJ_IO
(9)
OUTCCJ_IO
(9)
CASC_OUTPJ_DC
(6),
DRIFT
Symbol
standard.
post-scale counter K value. Therefore, if the counter K has a value of 2, the frequency reported can be lower than the f
than 120 ps.
to the intrinsic jitter of the PLL, when an input jitter of 30 ps is applied. The external memory interface clock output jitter specifications use a
different measurement method and are available in
A. Upstream PLL: 0.59Mhz
B. Downstream PLL: Downstream PLL BW > 2 MHz
page
REF
(7)
Table
is fIN/N when N = 1.
1–60.
(6),
(6),
(6)
1–34:
Cycle to Cycle Jitter for dedicated clock output
(F
Cycle to Cycle Jitter for dedicated clock output
(F
Period Jitter for clock output on regular I/O
(F
Period Jitter for clock output on regular I/O
(F
Cycle to Cycle Jitter for clock output on regular I/O
(F
Cycle to Cycle Jitter for clock output on regular I/O
(F
Period Jitter for dedicated clock output in cascaded PLLs
(F
Period Jitter for dedicated clock output in cascaded PLLs
(F
Frequency drift after PFDENA is disabled for duration of
100 us
OUT
OUT
OUT
OUT
OUT
OUT
OUT
OUT
≥ 100 MHz)
≥ 100 MHz)
< 100 MHz)
< 100 MHz)
≥ 100 MHz)
< 100 MHz)
< 100MHz)
≥100MHz)

Upstream PLL BW < 1 MHz
Parameter
–12
(14 sigma, 99.99999999974404% confidence level). The output jitter specification applies
Table 1–50 on page
MAX
or F
OUT
of the PLL.
1–61.
Chapter 1: DC and Switching Characteristics for Stratix IV Devices
Min
—
—
—
—
—
—
—
—
—
Typ
—
—
—
—
—
—
—
—
—
December 2011 Altera Corporation
Max
17.5
175
600
600
250
±10
60
60
25
Switching Characteristics
VCO
Table 1–48 on
specification.
mUI (p-p)
mUI (p-p)
mUI (p-p)
mUI (p-p)
ps (p-p)
ps (p-p)
ps (p-p)
ps (p-p)
Unit
%