LMC1982CIV National Semiconductor, LMC1982CIV Datasheet
LMC1982CIV
Specifications of LMC1982CIV
Available stocks
Related parts for LMC1982CIV
LMC1982CIV Summary of contents
Page 1
... Features n Low noise and distortion n Two pairs of stereo inputs Block and Connection Diagrams DNR ® registered trademark of National Semiconductor Corporation. Dolby ® registered trademark of Dolby Labs. © 2000 National Semiconductor Corporation n Enhanced stereo function n Loudness compensation n 40 position 2 dB/step volume attenuator plus mute ...
Page 2
... Infrared, (15 Seconds) 15V ESD Susceptability (Note 5) + GND − 0. 0.2V Operating Ratings 5 mA Temperature Range 20 mA LMC1982CIN, LMC1982CIV 500 mW Supply Voltage Range (V +125˚C −65˚C to +150˚ 9V kHz, input signal (300 mV) applied to INPUT 1, volume = 0 dB, bass = IN Conditions Clipping Level (1,.0% THD), Select Out (Pins 6, 23) Left and Right channels ...
Page 3
Electrical Characteristics The following specifications apply for V 0 dB, treble = 0 dB, enhanced stereo is off, and loudness is off unlessotherwise specified. All limits apply for T Symbol Parameter Channel-to-Channel Volume Tracking Error Mute Attenuation Bass Gain Range ...
Page 4
Electrical Characteristics Note 4: The maximum power dissipation must be derated at elevated temperatures and is dictated by T allowable power dissipation − JMAX +125˚C, and the typical junction-to-ambient thermal resistance, when board mounted, ...
Page 5
Typical Performance Characteristics Tone Control Response with Equal Bass and Treble Control Settings DS011028-22 (Continued) Loudness Response vs Frequency DS011028-23 5 Select Input Impedance vs Frequency DS011028-24 www.national.com ...
Page 6
... ID (27) DATA (28) 6 DS011028-12 Top View Order Number LMC1982CIV See NS Package Number V28A The output signal on these pins is a voltage taken from the volume attenuator’s −40 dB tap point. An external R–C network is con- nected to these pins. An external R–C network is connected across these pins ...
Page 7
Pin Description (Continued) TABLE 1. IM Bus Programming Codes for LMC1982 Address (A7–A0) 01000000 Input Select + Mute 01000001 Loudness, Enhanced Stereo 01000010 01000011 01000100 01000101 01000110 01000111 Read Digital Input 1 General Information The LMC1982 is a CMOS/bipolar building ...
Page 8
General Information (Continued) are serially shifted from the controller to the LMC1982. This is followed by 8 bits of function value data. Data present in the internal shift register is latched and the instruction is executed. Application Information INPUT SELECTOR ...
Page 9
Application Information if the total emitter current exceeds 5 mA. Thus, maximum output voltage can be increased and much lower distortion levels can be achieved using load impedances of at least INPUT IMPEDANCE The input impedance of ...
Page 10
Application Information The bass turn-over frequency is nominally when maximum boost is chosen. The inflection points (the frequencies where the boost or cut is within the final value) are for treble and bass FIGURE 3. System Block ...
Page 11
Application Information As shown in Table 1 , loudness and enhanced stereo are controlled through the same address important to re- member to set both functions to the correct value any time either of these functions is updated. ...
Page 12
Application Information FIGURE 7. LMC1982’s INTERMETAL Serial Bus Timing www.national.com (Continued) 12 DS011028-11 ...
Page 13
Physical Dimensions inches (millimeters) unless otherwise noted Order Number LMC1982CIN NS Package Number N28B 13 www.national.com ...
Page 14
... National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. inches (millimeters) unless otherwise noted (Continued) Order Number LMC1982CIV NS Package Number V28A 2 ...