OP727 Analog Devices, OP727 Datasheet - Page 11
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
OP727
Manufacturer Part Number
OP727
Description
Precision Rail-to-Rail Output Single Supply Dual Op Amp
Manufacturer
Analog Devices
Datasheet
1.OP727.pdf
(16 pages)
Specifications of OP727
-3db Bandwidth
700kHz
Slew Rate
200mV/µs
Vos
30µV
Ib
5.5nA
# Opamps Per Pkg
2
Input Noise (nv/rthz)
15nV/rtHz
Vcc-vee
3V to 36V
Isy Per Amplifier
290µA
Packages
SOIC,SOP
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
OP727AR
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
OP727ARUZ
Manufacturer:
MAXIM
Quantity:
9 100
Part Number:
OP727ARUZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
OP727ARZ
Manufacturer:
ADI
Quantity:
3 000
Part Number:
OP727ARZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
When the input of an amplifier is more than a diode drop below
V
(V–) or the positive supply (V+), respectively, to the input pins
which can destroy the device. In the case of OP777/OP727/
OP747, differential voltages equal to the supply voltage will not
cause any problem (see Figure 3). OP777/OP727/OP747 has
built- in 500
inputs, to minimize the chances of damage. It is a good practice to
keep the current flowing into the inputs below 5 mA. In this con-
text it should also be noted that the high breakdown of the input
transistors removes the necessity for clamp diodes between the
inputs of the amplifier, a feature that is mandatory on many preci-
sion op amps. Unfortunately, such clamp diodes greatly interfere
with many application circuits such as precision rectifiers and
comparators. The OP777/OP727/OP747 series is free from such
limitations.
Many amplifiers misbehave when one or both of the inputs are
forced beyond the input common-mode voltage range. Phase
reversal is typified by the transfer function of the amplifier effectively
reversing its transfer polarity. In some cases this can cause lockup in
servo systems and may cause permanent damage or nonrecoverable
parameter shifts to the amplifier. Many amplifiers feature compensa-
tion circuitry to combat these effects, but some are only effective for
the inverting input. Additionally, many of these schemes only work
for a few hundred millivolts or so beyond the supply rails. OP777/
OP727/OP747 has a protection circuit against phase reversal
when one or both inputs are forced beyond their input common-
mode voltage range. It is not recommended that the parts be
continuously driven more than 3 V beyond the rails.
REV.
EE
Figure 3b. Input Voltage Can Exceed the Supply Voltage
Without Damage
, or above V
D
internal current limiting resistors, in series with the
Figure 3a. Unity Gain Follower
CC
V p-p = 32V
, large currents will flow from the substrate
V
IN
TIME – 400 s/DIV
30V
V
OP777/
OP727/
OP747
SY
V
OUT
=
15V
–11–
The CMOS output stage has excellent (and fairly symmetric) output
drive and with light loads can actually swing to within 1 mV of both
supply rails. This is considerably better than similar amplifiers
featuring (so-called) rail-to-rail bipolar output stages. OP777/
OP727/OP747 is stable in the voltage follower configuration and
responds to signals as low as 1 mV above ground in single supply
operation.
The output of the OP777/OP727/OP747 series amplifier is protected
from damage against accidental shorts to either supply voltage,
provided that the maximum die temperature is not exceeded on a
long-term basis (see Absolute Maximum Rating section). Current of
up to 30 mA does not cause any damage.
In the design of power supply control circuits, a great deal of design
effort is focused on ensuring a pass transistor’s long-term reliability
over a wide range of load current conditions. As a result, monitoring
Figure 6. Rail-to-Rail Operation
V
IN
Figure 4. No Phase Reversal
= 1mV
Figure 5. Follower Circuit
TIME – 10 s/DIV
V
IN
3.0
TIME – 400 s/DIV
V TO 30V
OP777/
OP727/
OP747
V
SY
V
V
OUT
OUT
=
= 1mV
15V
1.0mV