AD7912 Analog Devices, AD7912 Datasheet - Page 24
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD7912
Manufacturer Part Number
AD7912
Description
2-Channel, 2.35 V to 5.25 V, 1 MSPS, 10-Bit A/D Converter
Manufacturer
Analog Devices
Datasheet
1.AD7912.pdf
(32 pages)
Specifications of AD7912
Resolution (bits)
10bit
# Chan
2
Sample Rate
1MSPS
Interface
Ser,SPI
Analog Input Type
SE-Uni
Ain Range
Uni Vdd
Adc Architecture
SAR
Pkg Type
SOP,SOT
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
AD7912ARMZ
Manufacturer:
ADI
Quantity:
1 000
Part Number:
AD7912ARMZ
Manufacturer:
ADI/亚德诺
Quantity:
20 000
Company:
Part Number:
AD7912ARMZ-REEL
Manufacturer:
ADI
Quantity:
1 000
Company:
Part Number:
AD7912AUJZ-REEL7
Manufacturer:
SIPEX
Quantity:
6 000
AD7912/AD7922
POWER VS. THROUGHPUT RATE
By using the power-down mode on the AD7912/AD7922 when
not converting, the average power consumption of the ADC
decreases at lower throughput rates. Figure 36 shows how, as the
throughput rate is reduced, the device remains in its power-
down state longer and the average power consumption over
time drops.
For example, if the AD7912/AD7922 are operating in a continu-
ous sampling mode with a throughput rate of 100 kSPS and a
SCLK of 18 MHz (V
power-down mode between conversions, then the power
consumption is calculated as follows. The power dissipation
during normal operation is 20 mW (V
time is one dummy cycle (1 µs), and the remaining conversion
time is another cycle (1 µs), then the AD7912/AD7922 dissipate
20 mW for 2 µs during each conversion cycle. If the throughput
rate is 100 kSPS and the cycle time is 10 µs, then the average
power dissipated during each cycle is
If V
down mode between conversions, then the power dissipation
during normal operation is 6 mW. The AD7912/AD7922 now
dissipate 6 mW for 2 µs during each conversion cycle. With a
throughput rate of 100 kSPS, the average power dissipated
during each cycle is
DD
(2/10) × (20 mW) = 4 mW
(2/10) × (6 mW) = 1.2 mW
= 3 V, SCLK = 18 MHz, and the device is again in power-
DD
= 5 V), and the devices are placed in the
DD
= 5 V). If the power-up
Rev. 0 | Page 24 of 32
In the previous calculations, the power dissipation when the
part is in power-down mode has not been taken into account.
By placing the parts into power-down mode between conver-
sions, the average power consumed by the ADC decreases as
the throughput rate decreases, because the ADC remains in a
power-down state for a longer time.
Figure 36 shows the power consumption versus throughput rate
when using the power-down mode between conversions with
both 5 V and 3 V supplies.
Power-down mode is intended for use with throughput rates of
approximately 330 kSPS and under, because at higher sampling
rates the short time spent in power-down does not affect the
average power consumed by the ADC.
0.01
100
0.1
10
1
0
Figure 36. Power Consumption vs. Throughput Rate
50
100
V
DD
THROUGHPUT (kSPS)
= 5V, SCLK = 18MHz
150
V
DD
200
= 3V, SCLK = 18MHz
250
300
350