AD9634 Analog Devices, AD9634 Datasheet - Page 22
![no-image](/images/manufacturer_photos/0/0/56/analog_devices_sml.jpg)
AD9634
Manufacturer Part Number
AD9634
Description
12-Bit, 170 MSPS/210 MSPS/250 MSPS, 1.8 V Analog-to-Digital Converter
Manufacturer
Analog Devices
Datasheet
1.AD9634.pdf
(32 pages)
Specifications of AD9634
Resolution (bits)
12bit
# Chan
1
Sample Rate
250MSPS
Interface
LVDS
Analog Input Type
Diff-Uni
Ain Range
1.75 V p-p
Adc Architecture
Pipelined
Pkg Type
CSP
AD9634
A third option is to ac couple a differential LVDS signal to the
sample clock input pins, as shown in Figure 55. The AD9510,
AD9511,AD9512, AD9513, AD9514, AD9515, AD9516, AD9517,
AD9518, AD9520, AD9522, AD9523,
excellent jitter performance.
CLOCK
CLOCK
Input Clock Divider
The
divide the input clock by integer values between 1 and 8. For
divide ratios other than 1, the DCS is enabled by default on
power-up.
Clock Duty Cycle
Typical high speed ADCs use both clock edges to generate a
variety of internal timing signals and, as a result, may be sensitive to
clock duty cycle. Commonly, a ±5% tolerance is required on the
clock duty cycle to maintain dynamic performance characteristics.
The
(falling) edge, providing an internal clock signal with a nominal
50% duty cycle. This allows the user to provide a wide range of
clock input duty cycles without affecting the performance of the
AD9634.
Jitter on the rising edge of the input clock is still of paramount
concern and is not reduced by the duty cycle stabilizer. The duty
cycle control loop does not function for clock rates less than
40 MHz nominally. The loop has a time constant associated
with it that must be considered when the clock rate may change
dynamically. A wait time of 1.5 μs to 5 μs is required after a
dynamic clock frequency increase or decrease before the DCS loop
is relocked to the input signal. During the time that the loop is
not locked, the DCS loop is bypassed, and internal device timing
is dependent on the duty cycle of the input clock signal. In such
applications, it may be appropriate to disable the duty cycle
stabilizer. In all other applications, enabling the DCS circuit is
recommended to maximize ac performance.
INPUT
INPUT
AD9634
AD9634
50kΩ
Figure 55. Differential LVDS Sample Clock (Up to 625 MHz)
contains an input clock divider with the ability to
contains a DCS that retimes the nonsampling
0.1µF
0.1µF
50kΩ
AD95xx
LVDS DRIVER
AD9524
100Ω
0.1µF
0.1µF
clock drivers offer
CLK+
CLK–
ADC
Rev. 0 | Page 22 of 32
Jitter Considerations
High speed, high resolution ADCs are sensitive to the quality
of the clock input. The degradation in SNR at a given input
frequency (f
In the equation, the rms aperture jitter represents the root-
mean-square of all jitter sources, which include the clock input,
the analog input signal, and the ADC aperture jitter specification.
IF undersampling applications are particularly sensitive to jitter,
as shown in Figure 56.
In cases where aperture jitter may affect the dynamic range of the
AD9634, treat the clock input as an analog signal. In addition,
use separate power supplies for the clock drivers and the ADC
output driver to avoid modulating the clock signal with digital
noise. Low jitter, crystal controlled oscillators provide the best clock
sources. If the clock is generated from another type of source (by
gating, dividing, or another method), it should be retimed by the
original clock during the last step.
Refer to
System Performance, and
Systems and the Effects of Clock Phase Noise and Jitter, for more
information about jitter performance as it relates to ADCs.
SNR
80
75
70
65
60
55
50
AN-501 Application
Figure 56. AD9634-250 SNR vs. Input Frequency and Jitter
1
HF
= −10 log[(2π × f
IN
) due to jitter (t
0.05ps
0.2ps
0.5ps
1ps
1.5ps
MEASURED
INPUT FREQUENCY (MHz)
10
AN-756 Application
Note, Aperture Uncertainty and ADC
IN
J
) can be calculated by
× t
JRMS
)
2
+ 10
100
(
Note, Sampled
−
SNR
LF
/
10
)
]
1000