SAM9X35 Atmel Corporation, SAM9X35 Datasheet - Page 40
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
SAM9X35
Manufacturer Part Number
SAM9X35
Description
Manufacturer
Atmel Corporation
Datasheets
1.SAM9261.pdf
(248 pages)
2.SAM9X25.pdf
(45 pages)
3.SAM9X25.pdf
(1145 pages)
4.SAM9X25.pdf
(45 pages)
5.SAM9X25.pdf
(1325 pages)
Specifications of SAM9X35
Flash (kbytes)
0 Kbytes
Pin Count
217
Max. Operating Frequency
400 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
105
Ext Interrupts
105
Usb Transceiver
3
Usb Speed
Hi-Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
3
Uart
7
Can
2
Lin
4
Ssc
1
Ethernet
1
Sd / Emmc
2
Graphic Lcd
Yes
Video Decoder
No
Camera Interface
No
Adc Channels
12
Adc Resolution (bits)
10
Adc Speed (ksps)
440
Resistive Touch Screen
Yes
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
32
Self Program Memory
NO
External Bus Interface
1
Dram Memory
DDR/LPDDR, SDRAM/LPSDR
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
0.9 to 1.1
Fpu
No
Mpu / Mmu
No/Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
10.14 Pulse Width Modulation Controller (PWM)
10.15 Soft Modem (SMD)
40
SAM9X25
• 4 channels, one 32-bit counter per channel
• Common clock generator, providing Thirteen Different Clocks
• Independent channel programming
• Modulations and protocols
• Data compression and error correction
• Type I Caller ID (CID) decoding
• Sixty-three embedded and upgradeable country profiles
• Embedded AT commands
• SmartDAA
– A Modulo n counter providing eleven clocks
– Two independent Linear Dividers working on modulo n counter outputs
– Independent Enable Disable Commands
– Independent Clock Selection
– Independent Period and Duty Cycle, with Double Bufferization
– Programmable selection of the output waveform polarity
– Programmable center or left aligned output waveform
– V.90
– V.34
– V.32bis, V.32, V.22bis, V.22, V.23, V.21
– V.23 reverse, V.23 half-duplex
– Bell 212A/Bell 103
– V.29 FastPOS
– V.22bis fast connect
– V.80 Synchronous Access Mode
– V.44 data compression (V.92 model)
– V.42bis and MNP 5 data compression
– V.42 LAPM and MNP 2-4 error correction
– EIA/TIA 578 Class 1 and T.31 Class 1.0
– Call Waiting (CW) detection and Type II Caller ID decoding during data mode
– Extension pick-up detection
– Digital line protection
– Line reversal detection
– Line-in-use detection
– Remote hang-up detection
– Worldwide compliance
11054AS–ATARM–29-Jul-11