SAM3N1B Atmel Corporation, SAM3N1B Datasheet - Page 24
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
SAM3N1B
Manufacturer Part Number
SAM3N1B
Description
Manufacturer
Atmel Corporation
Specifications of SAM3N1B
Flash (kbytes)
64 Kbytes
Pin Count
64
Max. Operating Frequency
48 MHz
Cpu
Cortex-M3
# Of Touch Channels
17
Hardware Qtouch Acquisition
No
Max I/o Pins
34
Ext Interrupts
34
Quadrature Decoder Channels
2
Usb Speed
No
Usb Interface
No
Spi
3
Twi (i2c)
2
Uart
4
Ssc
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Adc Channels
10
Adc Resolution (bits)
10
Adc Speed (ksps)
384
Resistive Touch Screen
No
Dac Channels
1
Dac Resolution (bits)
10
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
8
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.62 to 3.6
Fpu
No
Mpu / Mmu
no / no
Timers
6
Output Compare Channels
6
Input Capture Channels
3
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
Yes
Table 6-1.
Notes:
6.2.1
24
SYSTEM_IO
bit number
1. If PB12 is used as PIO input in user applications, a low level must be ensured at startup to prevent Flash erase before the
2. In the product Datasheet Refer to: Slow Clock Generator of the Supply Controller section.
3. In the product Datasheet Refer to: 3 to 20 MHZ Crystal Oscillator information in the PMC section.
12
SAM3N Summary
7
6
5
4
-
-
-
-
Serial Wire JTAG Debug Port (SWJ-DP) Pins
user application sets PB12 into PIO mode.
System I/O Configuration Pin List.
TDO/TRACESWO
Default function
TCK/SWCLK
The SWJ-DP pins are TCK/SWCLK, TMS/SWDIO, TDO/SWO, TDI and commonly provided on
a standard 20-pin JTAG connector defined by ARM. For more details about voltage reference
and reset state, refer to
At startup, SWJ-DP pins are configured in SWJ-DP mode to allow connection with debugging
probe. Please refer to the Debug and Test Section of the product datasheet.
SWJ-DP pins can be used as standard I/Os to provide users more general input/output pins
when the debug port is not needed in the end application. Mode selection between SWJ-DP
mode (System IO mode) and general IO mode is performed through the AHB Matrix Special
Function Registers (MATRIX_SFR). Configuration of the pad for pull-up, triggers, debouncing
and glitch filters is possible regardless of the mode.
The JTAGSEL pin is used to select the JTAG boundary scan when asserted at a high level. It
integrates a permanent pull-down resistor of about 15 kΩ to GND, so that it can be left uncon-
nected for normal operations.
By default, the JTAG Debug Port is active. If the debugger host wants to switch to the Serial
Wire Debug Port, it must provide a dedicated JTAG sequence on TMS/SWDIO and
TCK/SWCLK which disables the JTAG-DP and enables the SW-DP. When the Serial Wire
Debug Port is active, TDO/TRACESWO can be used for trace.
The asynchronous TRACE output (TRACESWO) is multiplexed with TDO. So the asynchronous
trace can only be used with SW-DP, not JTAG-DP. For more information about SW-DP and
JTAG-DP switching, please refer to the Debug and Test Section.
TMS/SWDIO
after reset
ERASE
PB9
PB8
PA7
PA8
TDI
Other function
XOUT32
Table 3-1 on page
PB12
XIN32
XOUT
PB7
PB6
PB5
PB4
XIN
Constraints for
6.
normal start
Low Level at
startup
-
-
-
-
-
-
-
-
(1)
In Matrix User Interface Registers
Configuration Register in the Bus
Matrix section of the product
(Refer to the System I/O
See footnote
See footnote
Configuration
datasheet.)
11011AS–ATARM–04-Oct-10
(2)
(3)
below
below